P/N + Description + Content Search

Overview
The ATmega169PA is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega169PA achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed.

Features
• High Performance, Low Power AVR® 8-Bit Microcontroller
• Advanced RISC Architecture
   – 130 Powerful Instructions – Most Single Clock Cycle Execution
   – 32 x 8 General Purpose Working Registers
   – Fully Static Operation
   – Up to 16 MIPS Throughput at 16 MHz
   – On-Chip 2-cycle Multiplier
• High Endurance Non-volatile Memory segments
   – 16K Bytes of In-System Self-programmable Flash program memory
   – 512 Bytes EEPROM
   – 1K Bytes Internal SRAM
   – Write/Erase cycles: 10,000 Flash/100,000 EEPROM
   – Data retention: 20 years at 85°C/100 years at 25°C(1)
   – Optional Boot Code Section with Independent Lock Bits
      In-System Programming by On-chip Boot Program
      True Read-While-Write Operation
   – Programming Lock for Software Security
• JTAG (IEEE std. 1149.1 compliant) Interface
   – Boundary-scan Capabilities According to the JTAG Standard
   – Extensive On-chip Debug Support
   – Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface
• Peripheral Features
   – 4 x 25 Segment LCD Driver
   – Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode
   – One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode
   – Real Time Counter with Separate Oscillator
   – Four PWM Channels
   – 8-channel, 10-bit ADC
   – Programmable Serial USART
   – Master/Slave SPI Serial Interface
   – Universal Serial Interface with Start Condition Detector
   – Programmable Watchdog Timer with Separate On-chip Oscillator
   – On-chip Analog Comparator
   – Interrupt and Wake-up on Pin Change
• Special Microcontroller Features
   – Power-on Reset and Programmable Brown-out Detection
   – Internal Calibrated Oscillator
   – External and Internal Interrupt Sources
   – Five Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, and Standby
• I/O and Packages
– 54 Programmable I/O Lines
– 64-lead TQFP, 64-pad QFN/MLF and 64-pad DRQFN
• Speed Grade:
   – ATmega169PA: 0 - 16 MHz @ 1.8 - 5.5V
• Temperature range:
   – -40°C to 85°C Industrial
• Ultra-Low Power Consumption
   – Active Mode:
      1 MHz, 1.8V: 215 µA
      32 kHz, 1.8V: 8 µA (including Oscillator)
      32 kHz, 1.8V: 25 µA (including Oscillator and LCD)
   – Power-down Mode:
      0.1 µA at 1.8V
   – Power-save Mode:
      0.6 µA at 1.8V (Including 32 kHz RTC)

For Marvell DSP Switchers™

This power inductor was developed specifically for Marvell Semiconductors for use with their DSP Switcher™ Power Management chipsets 88PD8300 and 88PD830. It is also used in modules 88MD8200 and 88MD830 as well as in DB-88PD8300 Development Board.

[Marvell]

Serial ATA II 1:4 Port Multiplier Solution

[Coilcraft, Inc.]

For Marvell DSP Switchers™

This power inductor was developed specifically for Marvell Semiconductors for use with their DSP Switcher™ Power Management chipsets 88PD8300 and 88PD830. It is also used in modules 88MD8200 and 88MD830 as well as in DB-88PD8300 Development Board.

MarvellPXA320 Processor Series

Cost-Effective, Scalable Performance up to 806 MHz for Power-Efficient, High-End Multimedia Handsets, Embedded Solutions, and Enterprise-Class Devices

PRODUCT OVERVIEW

Leading the Marvell® PXA3xx processor family, the PXA320 processor, with scalable performance to 806 MHz, plus additional industry-leading processing features, enables outstanding compute and video performance for high-end, multimedia cell phones and PDAs, industrial embedded solutions, and enterprise-class devices. Built on a low-power 90 nanometer (nm) process technology, and with the ability to dynamically scale voltage and frequency on demand, the PXA320 supports today’s stringent requirements for longer battery life. 

KEY FEATURES AND PLATFORM BENEFITS

The PXA320 processor integrates the following features:

•Scalable, general-purpose processing up to 806 MHz, a 256 KB L2 cache, and a 32-bit DDR memory interface for richer end-user applications, such as browsing rich Web2.0 content or streaming video. Extended headroom allows for execution of multiple applications at the same time, which is a key requirement for today’s wireless client devices with advanced capabilities.

•Marvell® Scalable Power Manager technology for MIPS/mW power efficiency, delivering long battery life and enabling consumers to spend more time enjoying the rich features their devices and service providers offer.

•Intel®Wireless MMX™ 2 technology, a 2D graphics accelerator, and a 768 KB frame buffer designed to support VGA resolution streaming video enhance the user’s experience of popular usage models like video playback, video conferencing, camcorder functionality, video telephony, and digital TV.

•An enhanced set of peripherals eases connectivity to technologies like Wi-Fi, WiBro, WiMAX, and Bluetooth v1.2, and the Quick Capture interface supports camera sensors up to 2–3 megapixels (MP) for richer camera applications.

•Package options of a discrete 14x14 mm package and a 15x15 mm package-on-package (PoP) package with stacked NAND flash and mobile DDR memory enable sleek form-factors.

GENERAL DESCRIPTION
The ACT8898 is a complete, cost effective, highly-efficient ActivePMUTM power management solution, optimized for the unique power, voltage-sequencing, and control requirements of the Marvell Aspen processor.
   
FEATURES
• Optimized for Marvell Aspen Processors
• Three Step-Down DC/DC Converters
• Four Low-Dropout Linear Regulators
• I2CTM Serial Interface
• Advanced Enable/Disable Sequencing Controller
• Minimal External Components
• Tiny 5×5mm TQFN55-32 Package
    − 0.75mm Package Height
    − Pb-Free and RoHS Compliant
   
APPLICATIONS
• Personal Navigation Devices
• Portable Media Players
• Tablet Devices
• Smart Phones
• MIDs
   

PRODUCT OVERVIEW
The Marvell® Alaska® family of Gigabit Ethernet (GbE) over copper transceivers are the industrys lowest power, smallest form factor, highest performance, and highest port density solutions in volume production.

Overview

The Marvell® single-chip 88ALP01 triple function device integrates a NAND flash controller (with Reed-Solomon ECC), an SD/SDIO controller, and a CMOS Camera Module Interface Controller (CCIC). The device is ideally suited for laptop computing devices and other embedded applications.

OVERVIEW
The 88SM4140 is a Serial ATA (SATA) Port Multiplier (PM) that allows an active host connection to communicate with up to four device ports and one SEMB port. The 88SM4140 is used to consolidate the capacity of storage devices by allowing a single host SATA port to be connected to more than one SATA device. This port multiplier employs Marvell’s SATA 3.0 Gbps Physical Layer (Phy) technology.

FEATURES
General
■ 0.15 µm CMOS technology.
■ Supports SATA 1.5 Gbps and SATA 3.0 Gbps communication speed on host and device ports.
■ 1.2V and 3.3V power.
■ 80-pin LQFP ePad package.
■ Phy test mode.
■ Full scan for high production test coverage and Phy self-test.
■ One host port.
■ Four device ports.
■ Supports 20 MHz, 25 MHz, 30 MHz, and 40 MHz reference clocks.

Functional
The 88SM4140 supports the following features:
■ Issuing PMREQP to host.
■ 57600 bps UART access.
■ Spread-spectrum clocking transmission.
■ Serial ATA BIST over host and device links.
■ Asynchronous notification.
■ SAF-TE (Enclosure Management).
■ FIS-based switching in conjunction with the following Marvell SATA host controllers:
   ■ 88SX6042
   ■ 88SX7042
   ■ 88SE6145
   ■ 88SE6121
■ Marvell Specific Mode (optional).
   ■ Queued command-based switching mode for Marvell 88SX6041 and 88SX6081.
■ One SEMB port/SM bus port (optional).

Overview
The PAN9320 is a 2.4 GHz ISM band Wi-Fi-embedded module which includes a wireless radio and an MCU for easy integration of Wi-Fi connectivity into various electronic devices.

Features
• Fully embedded: integrated full-featured network stack
• Contains all necessary IoT functionality (Place & Play)
• Integrated webserver with AJAX/JSON for web applications
• No stack or software implementation needed on a host MCU
• Simultaneous support of Access-Point & Infrastructure mode
• Fully automatical IP configuration
• DHCP server offers IP configuration in AP mode
• Access by names (//yourdevice)
• Integrated TCP/IP network stack: IPv4, ARP, and AutoIP
• Supports TLS/SSL, https, and Wi-Fi security (WPA2) for secure data connection
• Over-the-Air firmware update
• Two UART interfaces (command and transparent data)
• Integrated QSPI flash memory for customer web contents and configuration file (externally extendable with additional 2 MByte)
• Coexistence interface for external co-located 2.4 GHz radios (e. g. Bluetooth)
• Programming via standard JTAG
• Evaluation Kit with pre-installed web application for quick prototyping available
• Evaluation and development tool WiFigurator for Windows
• Getting started tutorials, PC tool, quickstart guide
• Wide temperature range of -30 °C to 70 °C
• FCC-/IC-/CE-certified

Characteristics
• Surface Mount Type (SMT) 29.0 mm x 13.5 mm x 2.66 mm
• Marvell® 88W8782 WLAN System-on-Chip (SoC) and 88MC200 (MCU) inside
• Tx power up to +18 dBm @ IEEE 802.11b
• Rx sensitivity of -98 dBm @ IEEE 802.11b DSSS 1 Mbps
• 40 MHz channels up to 150 Mbps
• Power supply 3.0 to 3.6 V
• Current consumption 430 mA (Tx @ 11b, 11 Mbps) and 145 mA Rx
• Low power mode available