CS8406-DSZR View Datasheet(PDF) - Cirrus Logic

Part Name

Description

MFG CO.

CS8406-DSZR

192 kHz Digital Audio Interface Transmitter

Cirrus Logic 

CS8406

VD

VL

GND

RST

H/S

TXN

TXP

OMCK

ISCLK

ILRCK

SDIN

SFMT0

SFMT1

APMS

HWCK0

HWCK1

TCBLD

TCBL

CEN

V

U

COPY/C

EMPH

AUDIO

ORIG

6 Digital Power (Input) - Digital core power supply. Typically +3.3 V or +5.0 V.

23 Logic Power (Input) - Input/Output power supply. Typically +3.3 V or +5.0 V.

22 Ground (Input) - Ground for I/O and core logic.

Reset (Input) - When RST is low, the CS8406 enters a low power mode and all internal states are reset.

9

On initial power up, RST must be held low until the power supply is stable, and all input clocks are stable

in frequency and phase. This is particularly true in Hardware Mode with multiple CS8406 devices, where

synchronization between devices is important.

Hardware/Software Control Mode Select (Input) - Determines the method of controlling the operation

24

of the CS8406, and the method of accessing CS and U data. Hardware Mode provides an alternate

mode of operation, and access to CS and U data is provided by dedicated pins. To select Hardware

Mode, this pin should be permanently tied to VL.

25 Differential Line Drivers (Output) - These pins transmit biphase encoded data. The drivers are pulled

26 low while the CS8406 is in the reset state.

21 Master Clock (Input) - The frequency can be set through the HWCK[1:0] pins.

13 Serial Audio Bit Clock (Input/Output) - Serial bit clock for audio data on the SDIN pin.

12

Serial Audio Input Left/Right Clock (Input/Output) - Word rate clock for the audio data on the SDIN

pin.

14 Serial Audio Data Port (Input) - Audio data serial input pin.

4 Serial Audio Data Format Select (Input) - Selects the serial audio input port format. See Table 3 on

5 page 29.

10

Serial Audio Data Port Master/Slave Select (Input) - APMS should be connected to VL to set serial

audio input port as a master or connected to GND to set the port as a slave.

20 OMCK Clock Ratio Select (Input) - Selects the ratio of OMCK to the input sample rate (Fs). A pull-up to

27 VL or pull-down to GND is required to set the appropriate mode. See Table 4 on page 29.

11

Transmit Channel Status Block Direction (Input) - Connect TCBLD to VL to set TCBL as an output.

Connect TCBLD to GND to set TCBL as an input.

Transmit Channel Status Block Start (Input/Output) - When operated as output, TCBL is high during

15

the first sub-frame of a transmitted channel status block, and low at all other times. When operated as

input, driving TCBL high for at least three OMCK clocks will cause the next transmitted sub-frame to be

the start of a channel status block.

C Bit Enable (Input) - Determines how the channel status data bits are input. When CEN is low, Hard-

16

ware Mode A is selected, where the COPY/C, ORIG, EMPH and AUDIO pins are used to enter selected

channel status data. When CEN is high, Hardware Mode B is selected, where the COPY/C pin is used

to enter serial channel status data.

17

Validity Bit (Input) - In Hardware Modes A and B, the V pin input determines the state of the validity bit

in the outgoing AES3 transmitted data. This pin is sampled on both edges of the ILRCK.

18

User Data Bit (Input) - In Hardware Modes A and B, the U pin input determines the state of the user

data bit in the outgoing AES3 transmitted data. This pin is sampled on both edges of the ILRCK.

COPY Channel Status Bit/C Bit (Input) - In Hardware Mode A (CEN = 0), the COPY/C and ORIG pins

1

determine the state of the Copyright, Pro, and L Channel Status bits in the outgoing AES3 data stream,

see Table 2 on page 29. In Hardware Mode B, the COPY/C pin becomes the direct C bit input data pin,

which is sampled on both edges of LRCK.

Pre-Emphasis Indicator (Input) - In Hardware Mode A (CEN = 0), the EMPH pin low sets the 3 empha-

3 sis channel status bits to indicate 50/15 μs pre-emphasis of the transmitted audio data. If EMPH is high,

then the three EMPH channel status bits are set to 000, indicating no pre-emphasis.

19

Audio Channel Status Bit (Input) - In Hardware Mode A (CEN = 0), the AUDIO pin determines the

state of the audio/non audio Channel Status bit in the outgoing AES3 data stream.

ORIG Channel Status Bit Control (Input) - In Hardware Mode A (CEN = 0), the ORIG and COPY/C

28 pins determine the state of the Copyright, Pro, and L Channel Status bits in the outgoing AES3 data

stream, see Table 2 on page 29.

DS580F5

31

Share Link: