datasheetbank_Logo    Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name  
HOME  >>>  ADI  >>> ADM1485ARMZ PDF

ADM1485ARMZ Datasheet PDF - Analog Devices

Part NameDescriptionManufacturer
ADM1485ARMZ 5 V Low Power EIA RS-485 Transceiver ADI
Analog Devices ADI
ADM1485ARMZ Datasheet PDF : ADM1485ARMZ pdf   
ADM1485 image

The ADM1485 is a differential line transceiver suitable for high speed bidirectional data communication on multipoint bus transmission lines. It is designed for balanced data transmission and complies with both RS-485 and RS-422 EIA Standards. The part contains a differential line driver and a differential line receiver. Both the driver and the receiver may be enabled independently. When disabled, the outputs are three-stated.
The ADM1485 operates from a single 5 V power supply. Excessive power dissipation caused by bus contention or by output shorting is prevented by a thermal shutdown circuit. This feature forces the driver output into a high impedance state if, during fault condi tions, a significant temperature increase is detected in the internal driver circuitry.
Up to 32 transceivers may be connected simultaneously on a bus, but only one driver should be enabled at any time. It is important, therefore, that the remaining disabled drivers do not load the bus. To ensure this, the ADM1485 driver features high output impedance when disabled and also when powered down.
This minimizes the loading effect when the transceiver is not being used. The high impedance driver output is maintained over the entire common-mode voltage range from –7 V to +12 V.
The receiver contains a fail-safe feature that results in a logic high output state if the inputs are unconnected (floating).
The ADM1485 is fabricated on BiCMOS, an advanced mixed technology process combining low power CMOS with fast switching bipolar technology. All inputs and outputs contain protection against ESD; all driver outputs feature high source and sink current capability. An epitaxial layer is used to guard against latch-up.
The ADM1485 features extremely fast switching speeds. Minimal driver propagation delays permit transmission at typical data rates of 30 Mbps while low skew minimizes EMI interference.
The part is fully specified over the commercial and industrial temperature range and is available in PDIP, SOIC, and small MSOP packages.

   Meets EIA RS-485 Standard
   30 Mbps Data Rate
   Single 5 V Supply
   –7 V to +12 V Bus Common-Mode Range
   High Speed, Low Power BiCMOS
   Thermal Shutdown Protection
   Short-Circuit Protection
   Driver Propagation Delay: 10 ns
   Receiver Propagation Delay: 15 ns
   High-Z Outputs with Power Off
   Superior Upgrade for LTC1485
   Low Power RS-485 Systems
   DTE-DCE Interface
   Packet Switching
   Local Area Networks
   Data Concentration
   Data Multiplexers
   Integrated Services Digital Network (ISDN)

Page Links : 1  2  3  4  5  6  7  8  9  10  11  12 


Other manufacturer searches related to ADM1485ARMZ

Part NameDescriptionPDFManufacturer
DS36C278 Low Power Multipoint EIA-RS-485 Transceiver DS36C278 View National ->Texas Instruments
DS36C280N Slew Rate Controlled CMOS EIA-RS-485 Transceiver DS36C280N View National ->Texas Instruments
ST485B Low power RS-485/RS-422 transceiver ST485B View STMicroelectronics
ST485BD Low power RS-485 / RS-422 transceiver ST485BD View STMicroelectronics
ST490AB Low power high speed RS-485/RS-422 transceiver ST490AB View STMicroelectronics
ST485AB Very high speed low power RS-485/RS-422 transceiver ST485AB View STMicroelectronics
ST490 Low power high speed RS-485/RS-422 transceiver ST490 View STMicroelectronics
ST485ER ±15KV ESD protected, Low power RS-485/RS-422 transceiver ST485ER View STMicroelectronics

Share Link : 

한국어 简体中文 日本語 русский español

All Rights Reserved © 2014 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]