Description
The Gamewell-FCI Velociti™ Series, ABD-2F and addressable projected beam smoke sensor is uniquely suited to sense smoke in hostile environments or open areas with high ceilings where spot-type sensors are unsuitable or difficult to install and maintain. It is intended for use in the signaling line circuits with the E3 Series® ILI-MB-E3 and ILI-S-E3 (Velociti mode only). The ABD-2F consists of a combination transmitter/receiver unit and a reflector. When smoke enters the path between the unit and the reflector, it causes a reduction in the signal, and when the smoke level reaches the predetermined threshold, an alarm results.
Features
• Single-ended, reflective design
• Six (6), user-selectable sensitivity levels
• 16 to 328 foot (4.9 to 99.9 m) detection range
• Compatible with the E3 Series® ILI-MB-E3 and ILI-S-E3
• Integral sensitivity test feature (ABD-2SF)
• Digital display - no special tools required
• User-friendly alignment procedure
• Integral automatic gain control compensates for signal
deterioration from dust build-up
• Remote test station (optional)
Description :
MOSFET Car Radio Stereo Internal Amplifier Ic Sound Chip
Reference site :
https://www.drive2.ru/c/965018/
//monitor.espec.ws/section14/topic52982.html
2048-Bit Sstatic MOS RAM with I/O Ports ABD Timer
STMicroelectronics Analog ICs
GYROSCOPES
ST’s complete family of single-axis (yaw) and two-axis (pitch-and-roll, pitch-and-yaw) MEMS gyroscopes offers the industry’s widest full-scale range, from 30 to 6000°/s.
The innovatively designed sensors can provide two separate outputs for each axis at the same time – an unamplified output value for general detection of angular motion and a 4x amplification for high-resolution measurements that enhances design flexibility and the user experience.
Extension Modules for Slot SBCs
Description
The Gamewell-FCI Velociti® Series, ABD-2F and addressable projected beam smoke sensor is uniquely suited to sense smoke in hostile environments or open areas with high ceilings where spot-type sensors are unsuitable or difficult to install and maintain. It is intended for use in the signaling line circuits with the following sub-assemblies.
Features
• Includes a single-ended, reflective design.
• Has six user-selectable sensitivity levels.
• Spans a 16 to 328 foot (4.9 to 99.9 m) detection range.
• Compatible with the E3 Series® ILI-MB-E3 and ILI-S-E3
or the S3 Series, SLC-PM.
• Contains an integral sensitivity test feature (ABD-2SF).
• Designed with a digital display - no special tools
required.
• Provides a user-friendly alignment procedure.
• Offers an integral automatic gain control that
compensates for signal deterioration from dust build-up.
• Available with an optional Remote test station.
DESCRIPTION
The BD135 and BD139 are silicon epitaxial planar NPN transistors in Jedec SOT-32 plastic package, designed for AUDIO amplifiers and drivers utilizing complementary or quasi compementary circuits.
The complementary PNP types are BD136 and BD140 respectively.
■ STMicroelectronics PREFERRED
SALESTYPES
Description
This image sensor based on STMicroelectronics CMOS technology is Bayer colorised.
The sensor provides a raw digital video output which also contains embedded codes to facilitate external synchronisation.
The sensor interfaces to a range of STMicroelectronics companion processors for applications such as USB webcams and digital stills cameras.
Features
■640 x 480 VGA resolution
■1/4 inch format lens compatible
■On board 10 bit ADC
■On board voltage regulators
■Automatic dark calibration
■On board AUDIO amplifier
■I2C interface
■Low power suspend mode
■4 or 5 wire nibble output
■Framegrabber signals: QCK and FST
DESCRIPTION
The BD135 and BD139 are silicon Epitaxial Planar NPN transistors mounted in Jedec SOT-32 plastic package, designed for AUDIO amplifiers and drivers utilizing complementary or quasi-complementary circuits.
The complementary PNP types are BD136 and BD140 respectively.
■ STMicroelectronics PREFERRED
SALESTYPES
|