datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

P/N + Description + Content Search

Search Word's :
Description : 1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI

GENERAL DESCRIPTION
The W25Q16DW (16M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/QUAD SPI (XIP) and storing voice, text and data. The device operates on a single 1.65V to 1.95V power supply with current consumption as low as 4mA active and 1µA for power-down. All devices are offered in space saving packages.
The W25Q16DW ARRAY is organized into 8,192 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128 (32KB block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q16DW has 512 erasable sectors and 32 erasable blocks respectively. The small 4KB sectors allow for greater flexibility in applications that require data and parameter storage. (See figure 2.)
The W25Q16DW support the standard Serial Peripheral Interface (SPI), Dual/QUAD I/O SPI as well as 2-clocks instruction cycle QUAD Peripheral Interface (QPI): Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1 (DO), I/O2 (/WP), and I/O3 (/HOLD). SPI clock frequencies of up to 104MHz are supported allowing equivalent clock rates of 208MHz (104MHz x 2) for Dual I/O and 416MHz (104MHz x 4) for QUAD I/O when using the Fast Read Dual/QUAD I/O and QPI instructions. These transfer rates can outperform standard Asynchronous 8 and 16-bit Parallel Flash memories. The Continuous Read Mode allows for efficient memory access with as few as 8-clocks of instruction-overhead to read a 24-bit address, allowing true XIP (execute in place) operation.
A Hold pin, Write Protect pin and programmable write protection, with top or bottom ARRAY control, provide further control flexibility. Additionally, the device supports JEDEC standard manufacturer and device identification, a 64-bit Unique Serial Number and four 256-bytes Security Registers.

FEATURES
• Family of SpiFlash Memories
   – W25Q16DW: 16M-bit / 2M-byte (2,097,152)
   – Standard SPI: CLK, /CS, DI, DO, /WP, /Hold
   – Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
   – QUAD SPI: CLK, /CS, IO0, IO1, IO2, IO3
   – QPI: CLK, /CS, IO0, IO1, IO2, IO3
• Highest Performance Serial Flash
   – 104MHz Standard/Dual/QUAD SPI clocks
   – 208/416MHz equivalent Dual/QUAD SPI
   – 50MB/s continuous data transfer rate
   – More than 100,000 erase/program cycles
   – More than 20-year data retention
• Efficient “Continuous Read” and QPI Mode
   – Continuous Read with 8/16/32/64-Byte Wrap
   – As few as 8 clocks to address memory
   – QUAD Peripheral Interface (QPI) reduces
      instruction overhead
   – Allows true XIP (execute in place) operation
   – Outperforms X16 Parallel Flash
• Low Power, Wide Temperature Range
   – Single 1.65 to 1.95V supply
   – 4mA active current, <1µA Power-down (typ.)
   – -40°C to +85°C operating range
• Flexible Architecture with 4KB sectors
   – Uniform Sector Erase (4K-bytes)
   – Uniform Block Erase (32K and 64K-bytes)
   – Program 1 to 256 byte per programmable page
   – Erase/Program Suspend & Resume
• Advanced Security Features
   – Software and Hardware Write-Protect
   – Top/Bottom, 4KB complement ARRAY protection
   – Power Supply Lock-Down and OTP protection
   – 64-Bit Unique ID for each device
   – 4X256-Bytes Security Registers with OTP locks
   – Volatile & Non-volatile Status Register Bits
• Space Efficient Packaging
   – 8-pin SOIC 150(2)/208-mil
   – 8-pad WSON 6x5-mm
   – 16-pin SOIC 300-mil(2)
   – Contact Winbond for KGD and other options

Description : 3V 8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI

GENERAL DESCRIPTION
The W25Q80DV (8M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/QUAD SPI (XIP) and storing voice, text and data. The device operates on a single 2.7V to 3.6V power supply with current consumption as low as 1µA for power-down. All devices are offered in space-saving packages.
The W25Q80DV ARRAY is organized into 4,096 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128 (32KB block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q80DV has 256 erasable sectors and 16 erasable blocks respectively. The small 4KB sectors allow for greater flexibility in applications that require data and parameter storage. (See figure 2.)
The W25Q80DV supports the standard Serial Peripheral Interface (SPI), and a high performance Dual/QUAD output as well as Dual/QUAD I/O SPI: Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1 (DO), I/O2 (/WP), and I/O3 (/HOLD). SPI clock frequencies of up to 104MHz are supported allowing equivalent clock rates of 208MHz (104MHz x 2) for Dual I/O and 416MHz (104MHz x 4) for QUAD I/O when using the Fast Read Dual/QUAD I/O instructions. These transfer rates can outperform standard Asynchronous 8 and 16-bit Parallel Flash memories. A Hold pin, Write Protect pin and programmable write protection, with top, bottom or complement ARRAY control, provide further control flexibility. Additionally, the device supports JEDEC standard manufacturer and device identification with a 64-bit Unique Serial Number.

FEATURES
● Family of SpiFlash Memories
   – W25Q80DV: 8M-bit/1M-byte (1,048,576)
   – 256-byte per programmable page
   – Standard SPI: CLK,/CS,DI,DO,/WP,/Hold
   – Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
   – QUAD SPI: CLK, /CS, IO0, IO1, IO2, IO3
   – Uniform 4KB Sectors, 32KB & 64KB Blocks
● Highest Performance Serial Flash
   – 104MHz Dual/QUAD SPI clocks
   – 208/416MHz equivalent Dual/QUAD SPI
   – 50MB/S continuous data transfer rate
● Software and Hardware Write Protection
   – Write-Protect all or portion of memory
   – Enable/Disable protection with /WP pin
   – Top or bottom ARRAY protection
● Flexible Architecture with 4KB sectors
   – Uniform Sector/Block Erase (4/32/64-kbytes)
   – Program one to 256 bytes < 0.8ms
   – Erase/Program Suspend & Resume
   – More than 100,000 erase/write cycles
   – More than 20-year data retention
● Low Power, Wide Temperature Range
   – Single 2.7 to 3.6V supply
   – <1µA Power-down(typ.)
● Space Efficient Packaging(1):
   – 8-pin SOIC 150-mil/208mil, VSOP 150-mil
   – 8-pad WSON 6x5-mm, USON 2x3-mm
   – 8-pin PDIP 300-mil
   – 8-ball WLCSP
   – Contact Winbond for KGD and other options

Description : 3V 32M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI

1. GENERAL DESCRIPTION
The W25Q32BV (32M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/QUAD SPI (XIP) and storing voice, text and data. The device operates on a single 2.7V to 3.6V power supply with current consumption as low as 4mA active and 1µA for power-down.
The W25Q32BV ARRAY is organized into 16,384 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128 (32KB block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q32BV has 1,024 erasable sectors and 64 erasable blocks respectively. The small 4KB sectors allow for greater flexibility in applications that require data and parameter storage. (See figure 2.)
The W25Q32BV supports the standard Serial Peripheral Interface (SPI), and a high performance Dual/QUAD output as well as Dual/QUAD I/O SPI: Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1 (DO), I/O2 (/WP), and I/O3 (/HOLD). SPI clock frequencies of up to 104MHz are supported allowing equivalent clock rates of 208MHz (104MHz x 2) for Dual I/O and 320MHz (80MHz x 4) for QUAD I/O when using the Fast Read Dual/QUAD I/O instructions. These transfer rates can outperform standard Asynchronous 8 and 16-bit Parallel Flash memories. The Continuous Read Mode allows for efficient memory access with as few as 8-clocks of instruction-overhead to read a 24-bit address, allowing true XIP (execute in place) operation.

FEATURES
● Family of SpiFlash Memories
   – W25Q32BV: 32M-bit / 4M-byte (4,194,304)
   – 256-byte per programmable page
   – Standard SPI: CLK, /CS, DI, DO, /WP, /Hold
   – Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
   – QUAD SPI: CLK, /CS, IO0, IO1, IO2, IO3
● Highest Performance Serial Flash
   – 104MHz Dual SPI / 80MHz QUAD SPI clocks
   – 208/320MHz equivalent Dual/QUAD SPI
   – 40MB/S continuous data transfer rate
   – Up to 8X that of ordinary Serial Flash
   – More than 100,000 erase/program cycles(1)
   – More than 20-year data retention
● Efficient “Continuous Read Mode”
   – Low Instruction overhead
   – Continuous Read with 8/16/32/64-Byte Wrap
   – As few as 8 clocks to address memory
   – Allows true XIP (execute in place) operation
   – Outperforms X16 Parallel Flash
● Low Power, Wide Temperature Range
   – Single 2.7 to 3.6V supply
   – 4mA active current, <1µA Power-down (typ.)
   – -40°C to +85°C operating range
● Flexible Architecture with 4KB sectors
   – Uniform Sector/Block Erase (4/32/64K-bytes)
   – Program one to 256 bytes
   – Erase/Program Suspend & Resume
● Advanced Security Features
   – Software and Hardware Write-Protect
   – Top/Bottom, 4KB complement ARRAY protection
   – Power Supply Lock-Down and OTP protection
   – 64-Bit Unique ID for each device
   – Discoverable Parameters (SFDP) Register
   – 3X256-Byte Security Registers with OTP locks
   – Volatile & Non-volatile Status Register Bits
● Space Efficient Packaging(1)
   – 8-pin SOIC/VSOP 208-mil
   – 8-pad WSON 6x5-mm/8x6-mm
   – 16-pin SOIC 300-mil
   – 8-pin PDIP 300-mil
   – 24-ball TFBGA 8x6-mm (6x4/5x5 ball ARRAY)
   – Contact Winbond for KGD and other options

Description : 3V 16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI

GENERAL DESCRIPTION
The W25Q16DV (16M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/QUAD SPI (XIP) and storing voice, text and data. The device operates on a single 2.7V to 3.6V power supply with current consumption as low as 4mA active and 1µA for power-down.
The W25Q16DV ARRAY is organized into 8,192 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128 (32KB block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q16DV has 512 erasable sectors and 32 erasable blocks respectively. The small 4KB sectors allow for greater flexibility in applications that require data and parameter storage. (See figure 2.)
The W25Q16DV supports the standard Serial Peripheral Interface (SPI), and a high performance Dual/QUAD output as well as Dual/QUAD I/O SPI: Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1 (DO), I/O2 (/WP), and I/O3 (/HOLD). SPI clock frequencies of up to 104MHz are supported allowing equivalent clock rates of 208MHz (104MHz x 2) for Dual I/O and 416MHz (104MHz x 4) for QUAD I/O when using the Fast Read Dual/QUAD I/O instructions. These transfer rates can outperform standard Asynchronous 8 and 16-bit Parallel Flash memories. The Continuous Read Mode allows for efficient memory access with as few as 8-clocks of instruction-overhead to read a 24-bit address, allowing true XIP (execute in place) operation.

FEATURES
● Family of SpiFlash Memories
   – W25Q16DV: 16M-bit / 2M-byte (2,097,152)
   – 256-byte per programmable page
   – Standard SPI: CLK, /CS, DI, DO, /WP, /Hold
   – Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
   – QUAD SPI: CLK, /CS, IO0, IO1, IO2, IO3
● Highest Performance Serial Flash
   – 104MHz Dual SPI / QUAD SPI clocks
   – 208/416MHz equivalent Dual/QUAD SPI
   – 52MB/S continuous data transfer rate
   – Up to 8X that of ordinary Serial Flash
   – More than 100,000 erase/program cycles
   – More than 20-year data retention
● Efficient “Continuous Read Mode”
   – Low Instruction overhead
   – Continuous Read with 8/16/32/64-Byte Wrap
   – As few as 8 clocks to address memory
   – Allows true XIP (execute in place) operation
   – Outperforms X16 Parallel Flash
● Low Power, Wide Temperature Range
   – Single 2.7 to 3.6V supply
   – 4mA active current, <1µA Power-down (typ.)
   – -40°C to +85°C operating range
● Flexible Architecture with 4KB sectors
   – Uniform Sector/Block Erase (4/32/64K-bytes)
   – Program one to 256 bytes
   – Erase/Program Suspend & Resume
● Advanced Security & Identification Features
   – Software and Hardware Write-Protect
   – Top/Bottom, 4KB complement ARRAY protection
   – Power Supply Lock-Down and OTP protection
   – 64-Bit Unique ID for each device
   – Discoverable Parameters (SFDP) Register
   – 3X256-Byte Security Registers with OTP locks
   – Volatile & Non-volatile Status Register Bits
● Space Efficient Packaging(1)
   – 8-pin SOIC 150/208-mil
   – 8-pad WSON 6x5-mm
   – 8-pad USON 4X3mm / 4X4mm
   – 8-pin PDIP 300-mil
   – 16-pin SOIC 300-mil
   – 24-ball TFBGA 8x6-mm (6x4/5x5 ball ARRAY)
   – Contact Winbond for KGD and other options

Description : 3V 32M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI

[winbond]

GENERAL DESCRIPTION
The W25Q32BV (32M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/QUAD SPI (XIP) and storing voice, text and data. The device operates on a single 2.7V to 3.6V power supply with current consumption as low as 4mA active and 1µA for power-down.
The W25Q32BV ARRAY is organized into 16,384 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128 (32KB block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q32BV has 1,024 erasable sectors and 64 erasable blocks respectively. The small 4KB sectors allow for greater flexibility in applications that require data and parameter storage. (See figure 2.)
The W25Q32BV supports the standard Serial Peripheral Interface (SPI), and a high performance Dual/QUAD output as well as Dual/QUAD I/O SPI: Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1 (DO), I/O2 (/WP), and I/O3 (/HOLD). SPI clock frequencies of up to 104MHz are supported allowing equivalent clock rates of 208MHz (104MHz x 2) for Dual I/O and 320MHz (80MHz x 4) for QUAD I/O when using the Fast Read Dual/QUAD I/O instructions. These transfer rates can outperform standard Asynchronous 8 and 16-bit Parallel Flash memories. The Continuous Read Mode allows for efficient memory access with as few as 8-clocks of instruction-overhead to read a 24-bit address, allowing true XIP (execute in place) operation.

FEATURES
• Family of SpiFlash Memories
   – W25Q32BV: 32M-bit / 4M-byte (4,194,304)
   – 256-byte per programmable page
   – Standard SPI: CLK, /CS, DI, DO, /WP, /Hold
   – Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
   – QUAD SPI: CLK, /CS, IO0, IO1, IO2, IO3
• Highest Performance Serial Flash
   – 104MHz Dual SPI / 80MHz QUAD SPI clocks
   – 208/320MHz equivalent Dual/QUAD SPI
   – 40MB/S continuous data transfer rate
   – Up to 8X that of ordinary Serial Flash
   – More than 100,000 erase/program cycles(1)
   – More than 20-year data retention
• Efficient “Continuous Read Mode”
   – Low Instruction overhead
   – Continuous Read with 8/16/32/64-Byte Wrap
   – As few as 8 clocks to address memory
   – Allows true XIP (execute in place) operation
   – Outperforms X16 Parallel Flash
• Low Power, Wide Temperature Range
   – Single 2.7 to 3.6V supply
   – 4mA active current, <1µA Power-down (typ.)
   – -40°C to +85°C operating range
• Flexible Architecture with 4KB sectors
   – Uniform Sector/Block Erase (4/32/64K-bytes)
   – Program one to 256 bytes
   – Erase/Program Suspend & Resume
• Advanced Security Features
   – Software and Hardware Write-Protect
   – Top/Bottom, 4KB complement ARRAY protection
   – Power Supply Lock-Down and OTP protection
   – 64-Bit Unique ID for each device
   – Discoverable Parameters (SFDP) Register
   – 3X256-Byte Security Registers with OTP locks
   – Volatile & Non-volatile Status Register Bits
• Space Efficient Packaging
   – 8-pin SOIC 208-mil
   – 8-pad WSON 6x5-mm/8x6-mm(2)
   – 16-pin SOIC 300-mil
   – 8-pin PDIP 300-mil
   – 24-ball TFBGA 8x6-mm
   – Contact Winbond for KGD and other options

Description : SURFACE MOUNT LEDs, SOT-23 Package

SURFACE MOUNT LEDs, SOT-23 Package

SURFACE MOUNT, Bi-Color LEDs, SOT-23 Package

SURFACE MOUNT, Gull Wing LEDs

SURFACE MOUNT LEDs (Rectangular Lens)

SURFACE MOUNT LEDs (Round Lens)

SURFACE MOUNT LEDs with Resistor - 5V

SURFACE MOUNT LEDs with Resistor - 12V

SURFACE MOUNT, Bi-Color LEDs

SURFACE MOUNT Infrared LEDs: 880nm, 940nm

Low Profile SURFACE MOUNT LEDs (standard package 0805)

Low Profile SURFACE MOUNT LEDs (standard package 1206)

Right Angle/Side Lighting SURFACE MOUNT LEDs

Axial Lead LEDs

Description : 3V 128M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI

GENERAL DESCRIPTIONS
The W25Q128FV (128M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/QUAD SPI (XIP) and storing voice, text and data. The device operates on a single 2.7V to 3.6V power supply with current consumption as low as 4mA active and 1µA for power-down. All devices are offered in space saving packages.
The W25Q128FV ARRAY is organized into 65,536 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128 (32KB block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q128FV has 4,096 erasable sectors and 256 erasable blocks respectively. The small 4KB sectors allow for greater flexibility in applications that require data and parameter storage. (See Figure 2.)
A Hold pin, Write Protect pin and programmable write protection, with top or bottom ARRAY control, provide further control flexibility. Additionally, the device supports JEDEC standard manufacturer and device ID and SFDP Register, a 64-bit Unique Serial Number and three 256-bytes Security Registers.

FEATURES
• New Family of SpiFlash Memories
   – W25Q128FV: 128M-bit / 16M-byte
   – Standard SPI: CLK, /CS, DI, DO, /WP, /Hold
   – Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
   – QUAD SPI: CLK, /CS, IO0, IO1, IO2, IO3
   – QPI: CLK, /CS, IO0, IO1, IO2, IO3
   – Software & Hardware Reset
• Highest Performance Serial Flash
   – 104MHz Single, Dual/QUAD SPI clocks
   – 208/416MHz equivalent Dual/QUAD SPI
   – 50MB/S continuous data transfer rate
   – More than 100,000 erase/program cycles
   – More than 20-year data retention
• Efficient “Continuous Read” and QPI Mode
   – Continuous Read with 8/16/32/64-Byte Wrap
   – As few as 8 clocks to address memory
   – QUAD Peripheral Interface (QPI) reduces instruction overhead
   – Allows true XIP (execute in place) operation
   – Outperforms X16 Parallel Flash
• Low Power, Wide Temperature Range
   – Single 2.7 to 3.6V supply
   – 4mA active current, <1µA Power-down (typ.)
   – -40°C to +85°C operating range
• Flexible Architecture with 4KB sectors
  – Uniform Sector/Block Erase (4K/32K/64K-Byte)
  – Program 1 to 256 byte per programmable page
  – Erase/Program Suspend & Resume
• Advanced Security Features
   – Software and Hardware Write-Protect
   – Power Supply Lock-Down and OTP protection
   – Top/Bottom, Complement ARRAY protection
   – Individual Block/Sector ARRAY protection
   – 64-Bit Unique ID for each device
   – Discoverable Parameters (SFDP) Register
   – 3X256-Bytes Security Registers with OTP locks
   – Volatile & Non-volatile Status Register Bits
• Space Efficient Packaging
   – 8-pin SOIC / VSOP 208-mil
   – 8-pin PDIP 300-mil
   – 8-pad WSON 6x5-mm / 8x6-mm
   – 16-pin SOIC 300-mil (additional /RESET pin)
   – 24-ball TFBGA 8x6-mm
   – Contact Winbond for KGD and other options

Description : SURFACE MOUNT 1.0 W GLASS ZENER DIODES

DESCRIPTION
This SURFACE MOUNTable 1 watt ZENER DIODE series is electrically equivalent to the 1N4728A thru 1N4764A registration in the DO-41 equivalent package except that it meets the JEDEC SURFACE MOUNT outline DO-213AB. It is an ideal selection for applications of high density and low parasitic requirements for voltage regulation. Standard voltage tolerance is +/- 5% with tighter tolerances available down to 1%. With its glass hermetic qualities, it may also be used for high reliability applications when required by a source control drawing (SCD).

FEATURES
• Electrically similar to the JEDEC registered 1N4728 thru 1N4764 ZENER series
ZENER voltages available 3.3V to 100V
• Standard voltage tolerances are +/- 5% with “A” suffix and 10 % with no suffix identification
• Tight tolerances available in plus or minus 2% or 1% with C or D suffix respectively
• Options for screening in accordance with MIL-PRF-19500 for JAN, JANTX, JANTXV, and JANS are available by adding MQ, MX, MV, or MSP prefixes respectively to part numbers.
SURFACE MOUNT equivalents also available as SMAJ4728A to SMAJ4764A and SMAJ4728A to SMAJ4764A
• Plastic body axial-leaded ZENER equivalents are also available as 1N4728A to 1N4764A

APPLICATIONS / BENEFITS
• Regulates voltage over a broad operating current and temperature range
• Wide selection from 3.3 to 100 V
• Leadless package for SURFACE MOUNTing
• Ideal for high density MOUNTing
• Nonsensitive to ESD
• Hermetically sealed glass package
• Specified capacitance (see Figure 2)
• Inherently radiation hard per MicroNote 050

PanJit
PANJIT INTERNATIONAL
Description : QUAD TVS/ZENER ARRAY FOR ESD AND LATCH-UP PROTECTION

This QUAD TVS/ZENER ARRAY family have been designed to Protect Sensitive Equipment against ESD and to prevent Latch-Up events in CMOS circuitry operating at 5V, 12V, 15V and 24V. This TVS ARRAY offers an integrated solution to protect up to 4 data lines where the board space is a premium.

SPECIFICATION FEATURES
350W Power Dissipation (8/20µs Waveform)
Low Leakage Current, Maximum of 5µA at rated voltage
IEC61000-4-2 ESD 20kV air, 15kV Contact Compliance
Very Low Clamping Voltage
Industry Standard SURFACE MOUNT Package SOT23-6L
100% Tin Matte Finish (RoHS Compliance)

APPLICATIONS
Personal Digital Assistant (PDA)
SIM Card Port Protection (Mobile Phone)
Portable Instrumentation
Mobile Phones and Accessories
Memory Card Port Protection

Description : 1.8V 32M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI

GENERAL DESCRIPTIONS
The W25Q32FW (32M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/QUAD SPI (XIP) and storing voice, text and data. The device operates on a single 1.65V to 1.95V power supply with current consumption as low as 4mA active and 1µA for power-down. All devices are offered in space-saving packages.
The W25Q32FW ARRAY is organized into 32,768 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128 (32KB block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q32FW has 1,024 erasable sectors and 64 erasable blocks respectively. The small 4KB sectors allow for greater flexibility in applications that require data and parameter storage. (See Figure 2.)

FEATURES
● New Family of SpiFlash Memories
   – W25Q32FW: 32M-bit / 4M-byte
   – Standard SPI: CLK, /CS, DI, DO, /WP, /Hold
   – Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
   – QUAD SPI: CLK, /CS, IO0, IO1, IO2, IO3
   – QPI: CLK, /CS, IO0, IO1, IO2, IO3
   – Software & Hardware Reset
● Highest Performance Serial Flash
   – 104MHz Single, Dual/QUAD SPI clocks
   – 208/416MHz equivalent Dual/QUAD SPI
   – 50MB/S continuous data transfer rate
   – Min 100K Program-Erase cycles per secto
   – More than 20-year data retention
● Efficient “Continuous Read” and QPI Mode
   – Continuous Read with 8/16/32/64-Byte Wrap
   – As few as 8 clocks to address memory
   – QUAD Peripheral Interface (QPI) reduces instruction overhead
   – Allows true XIP (execute in place) operation
   – Outperforms X16 Parallel Flash
● Flexible Architecture with 4KB sectors
   – Uniform Sector/Block Erase (4K/32K/64K-Byte)
   – Program 1 to 256 byte per programmable page
   – Erase/Program Suspend & Resume
● Advanced Security Features
   – Software and Hardware Write-Protect
   – Power Supply Lock-Down and OTP protection
   – Top/Bottom, Complement ARRAY protection
   – Individual Block/Sector ARRAY protection
   – 64-Bit Unique ID for each device
   – Discoverable Parameters (SFDP) Register
   – 3X256-Bytes Security Registers with OTP locks
   – Volatile & Non-volatile Status Register Bits
● Space Efficient Packaging
   – 8-pin SOIC/VSOP 208-mil, XSON 4x4-mm
   – 8-pad WSON 6x5-mm / 8x6-mm
   – 16-pin SOIC 300-mil (additional /RESET)
   – 24-ball TFBGA 8x6-mm(additional /RESET)
   – 12-ball WLCSP
   – Contact Winbond for KGD and other options

12345678910 Next

All Rights Reserved© datasheetbank.com  [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]