datasheetbank_Logo     Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

P/N + Description + Content Search

Search Words :

Part Name(s) : DZPD6710VCB PD6710 PD6722 SPD6722QCCE DZPD6722VCCE Intel
Intel
Description : ISA-to-PC-CARD (PCMCIA) CONTROLLERS View

The PD6710 and PD6722 are single-chip PC CARD (PCMCIA) controller solutions capable of controlling one (PD6710) or two (PD6722) PC CARD sockets. The chips are compliant with PC CARD Standard, PCMCIA 2.1, and JEIDA 4.1 and are optimized for use in embedded applications and notebook/handheld/mobile computer systems where reduced form factor and low power consumption are critical design objectives. With the PD6710, a complete PC CARD solution with power-control logic can occupy less than 1.5 square inches (excluding the socket connector). With the PD6722, a complete dual-socket PC CARD solution with power-control logic can occupy less than 2 square inches (excluding socket connectors).

Product Features
• Single-chip PC CARD (PCMCIA) CONTROLLERS
• Direct connection to ISA (PC AT) bus and one or two PC CARD sockets
• Compliant with PC CARD Standard, PCMCIA 2.1, and JEIDA 4.1
• 82365SL-compatible register set, ExCA-compatible
• Automatic Low-Power Dynamic mode for lowest active power consumption
• Programmable Suspend mode
• Hardware-enabled Super Suspend mode
• Five programmable memory windows per socket and two programmable I/O windows per socket
• Programmable CARD access cycle timing
• 8- or 16-bit system bus interface
• 8- and 16-bit PC CARD interface support
PCMCIA-ATA and ture-IDE disk interface support
• DMA support (PD6722)
CARD-voltage sense support
PC CARD activity indicator
• Mixed-voltage operation (3.3/5.0 V)
• Single-socket interface: 144-pin LQFP for smallest form factor (PD6710)
• Dual-socket interface: 208-pin MQFP or LQFP (PD6722)

Part Name(s) : TPS2201YDB TPS2201YDF TI
Texas Instruments
Description : DUAL-SLOT PC CARD POWER-INTERFACE SWITCHES FOR PARALLEL PCMCIA CONTROLLERS View

description
The TPS2201 PC CARD (PCMCIA) power interface switch provides an integrated power-management solution for two PC CARDs. All of the discrete power MOSFETs, a logic section, current limiting, thermal protection, and power-good reporting for PC CARD control are combined on a single integrated circuit (IC), using Texas Instruments LinBiCMOS™ process. The circuit allows the distribution of 3-V, 5-V and/or 12-V CARD power and is compatible with most PCMCIA CONTROLLERS. The current-limiting feature eliminates the need for fuses, which reduces component count and improves reliability; current-limit reporting can help the user isolate a system fault to a bad CARD.

• Fully Integrated VCC and Vpp Switching for Dual-Slot PC CARD Interface
• Compatible With CONTROLLERS From Cirrus, Intel, and Texas Instruments
• Meets PCMCIA Standards
• Internal Charge Pump (No External Capacitors Required) – 12-V Supply Can Be Disabled Except for Programming
• Short Circuit and Thermal Protection
• Space Saving SSOP (DB) Package
• Compatible With 3.3-V, 5-V and 12-V PC CARDs
• Power Saving IDD = 83 µA Typ, IQ = 1 µA
• Low rDS(on) (160-mΩ VCC Switch)
• Break-Before-Make Switching

Part Name(s) : TPS2201 TPS2201DB TPS2201DF TPS2201I TPS2201IDB TPS2201IDF TPS2201Y TPS2201IDBR TPS2201IDFR Texas-Instruments
Texas Instruments
Description : DUAL-SLOT PC CARD POWER-INTERFACE SWITCHES FOR PARALLEL PCMCIA CONTROLLERS View

description
The TPS2201 PC CARD (PCMCIA) power interface switch provides an integrated power-management solution for two PC CARDs. All of the discrete power MOSFETs, a logic section, current limiting, thermal protection, and power-good reporting for PC CARD control are combined on a single integrated circuit (IC), using Texas Instruments LinBiCMOS™ process. The circuit allows the distribution of 3-V, 5-V and/or 12-V CARD power and is compatible with most PCMCIA CONTROLLERS. The current-limiting feature eliminates the need for fuses, which reduces component count and improves reliability; current-limit reporting can help the user isolate a system fault to a bad CARD.

● Fully Integrated VCC and Vpp Switching for Dual-Slot PC CARD™ Interface
● Compatible With CONTROLLERS From Cirrus, Intel, and Texas Instruments
● Meets PCMCIA Standards
● Internal Charge Pump (No External Capacitors Required) – 12-V Supply Can Be Disabled Except for Programming
● Short-Circuit and Thermal Protection
● Space Saving SSOP (DB) Package
● For 3.3-V, 5-V and 12-V PC CARDs
● Power Saving IDD = 83 µA Typ, IQ = 1 µA
● Low rDS(on) (160-mΩ VCC Switch)
● Break-Before-Make Switching

Part Name(s) : TPS2201 TPS2201DF TPS2201DB TPS2201I TPS2201IDB TPS2201IDBLE TPS2201IDBR TPS2201IDBRG4 TPS2201IDF TPS2201IDFLE TPS2201IDFR TPS2201Y TI
Texas Instruments
Description : DUAL-SLOT PC CARD POWER-INTERFACE SWITCHES FOR PARALLEL PCMCIA CONTROLLERS View

description
The TPS2201 PC CARD (PCMCIA) power interface switch provides an integrated power-management solution for two PC CARDs. All of the discrete power MOSFETs, a logic section, current limiting, thermal protection, and power-good reporting for PC CARD control are combined on a single integrated circuit (IC), using Texas Instruments LinBiCMOS™ process. The circuit allows the distribution of 3-V, 5-V and/or 12-V CARD power and is compatible with most PCMCIA CONTROLLERS. The current-limiting feature eliminates the need for fuses, which reduces component count and improves reliability; current-limit reporting can help the user isolate a system fault to a bad CARD.

● Fully Integrated VCC and Vpp Switching for Dual-Slot PC CARD Interface
● Compatible With CONTROLLERS From Cirrus, Intel, and Texas Instruments
● Meets PCMCIA Standards
● Internal Charge Pump (No External Capacitors Required) – 12-V Supply Can Be Disabled Except for Programming
● Short-Circuit and Thermal Protection
● Space Saving SSOP (DB) Package
● For 3.3-V, 5-V and 12-V PC CARDs
● Power Saving IDD = 83 µA Typ, IQ = 1 µA
● Low rDS(on) (160-mΩ VCC Switch)
● Break-Before-Make Switching


Part Name(s) : PCI1410A PCI1410APGEG4 PCI1410AGHK PCI1410AGGU PCI1410APGE TI
Texas Instruments
Description : PC CARD CONTROLLERS View

DESCRIPTION
The TI™ PCI1410A device is a high-performance PCI-to-PC CARD controller that supports a single PC CARD socket compliant with the PC CARD Standard. The PCI1410A device provides features that make it the best choice for bridging between PCI and PC CARDs in both notebook and desktop computers. The PC CARD Standard retains the 16-bit PC CARD specification defined in PCI Local Bus Specification and defines the new 32-bit PC CARD, CARDBus, as being capable of full 32-bit data transfers at 33 MHz. The PCI1410A device supports both 16-bit and CARDBus PC CARDs, powered at 5 V or 3.3 V, as required.

FEATURES
• Ability to wake from D3hot and D3cold
• Full compatiblity with the Intel 430TX (Mobile
   Triton II) chipset
• A 144-terminal low-profile QFP (PGE),
   144-terminal MicroStar BGA™ ball grid array
   (GGU) package, or 209-terminal MicroStar
   BGA™ (GHK) package
• 3.3-V core logic with universal PCI interfaces
   compatible with 3.3-V and 5-V PCI signaling
   environments
• Mix-and-match 5-V/3.3-V 16-bit PC CARDs and
   3.3-V CARDBus CARDs
• Single PC CARD or CARDBus slot with hot
   insertion and removal
• Burst transfers to maximize data throughput
   on the PCI bus and the CARDBus bus
• Parallel PCI interrupts, parallel ISA IRQ and
   parallel PCI interrupts, serial ISA IRQ with
   parallel PCI interrupts, and serial ISA IRQ and
   PCI interrupts
• Serial EEPROM interface for loading
   subsystem ID and subsystem vendor ID
• Pipelined architecture allows greater than 130
   Mbit/s sustained throughput from CARDBus to
   PCI and from PCI to CARDBus
• Interface to parallel single-slot PC CARD
   power-switch interfaces like the TI™ TPS2211
   device (Continue ...)

Part Name(s) : PCI1221 PCI1221PDV PCI1221GHK TI
Texas Instruments
Description : PC CARD CONTROLLERS View

description
The TI PCI1221 is a high-performance PCI-to-PC CARD controller that supports two independent CARD sockets compliant with the 1997 PC CARD Standard. The PCI1221 provides a rich feature set that makes it the best choice for bridging between PCI and PC CARDs in both notebook and desktop computers. The 1997 PC CARD Standard retains the 16-bit PC CARD specification defined in PCMCIA Release 2.2 and defines the new 32-bit PC CARD, CARDBus, capable of full 32-bit data transfers at 33 MHz. The PCI1221 supports any combination of 16-bit and CARDBus PC CARDs in the two sockets, powered at 5 V or 3.3 V, as required.

PCI Bus Power Management Interface Specification 1.0 Compliant
● ACPI 1.0 Compliant
● Fully Compatible With the Intel 430TX (Mobile Triton II) Chipset
● Packaged in a 208-Pin Low-Profile QFP (PDV) or GHK High Density Ball Grid Array (BGA)
PCI Local Bus Specification Revision 2.2 Compliant
● 1997 PC CARD Standard Compliant
PC 99 Compliant
● 3.3-V Core Logic With Universal PCI Interfaces Compatible With 3.3-V and 5-V PCI Signaling Environments
● Mix-and-Match 5-V/3.3-V 16-bit PC CARDs and 3.3-V CARDBus CARDs
● Supports Two PC CARD or CARDBus Slots With Hot Insertion and Removal
● Uses Serial Interface to TI TPS2202/2206 Dual-Slot PC CARD Power Switch
● Supports Burst Transfers to Maximize Data Throughput on the PCI Bus and CARDBus Bus
● Supports Parallel PCI Interrupts, Parallel ISA IRQ and Parallel PCI Interrupts, Serial ISA IRQ With Parallel PCI Interrupts, and Serial ISA IRQ and PCI Interrupts
● Pipelined Architecture Allows Greater Than 130M-Bps Throughput From CARDBus-to-PCI and From PCI-to-CARDBus
● Supports Up to Five General-Purpose I/Os
● Serial EEPROM Interface for Loading Subsystem ID and Subsystem Vendor ID
● Programmable Output Select for CLKRUN
● Multifunction PCI Device With Separate Configuration Space for Each Socket
● Five PCI Memory Windows and Two I/O Windows Available for Each R2 Socket
● Two I/O Windows and Two Memory Windows Available to Each CARDBus Socket
● Exchangeable CARD Architecture (ExCA) Compatible Registers Are Mapped in Memory and I/O Space
● Intel 82365SL-DF Register Compatible
● Supports Ring Indicate, SUSPEND, PCI CLKRUN, and CARDBus CCLKRUN
● LED Activity Pins
● Supports PCI Bus Lock (LOCK)
● Advanced Submicron, Low-Power CMOS Technology

Part Name(s) : PCI1410 PCI1410ARFP PCI1410GGU PCI1410GHK PCI1410PGE PCI1410RFP TI
Texas Instruments
Description : PC CARD CONTROLLERS View

Description
The TI™ PCI1410 is a high-performance PCI-to-PC CARD controller that supports a single PC CARD socket compliant with the 1997 PC CARD Standard. The PCI1410 provides features that make it the best choice for bridging between PCI and PC CARDs in both notebook and desktop computers. The 1997 PC CARD Standard retains the 16-bit PC CARD specification defined in PCI Local Bus Specification and defines the new 32-bit PC CARD, CARDBus, capable of full 32-bit data transfers at 33 MHz. The PCI1410 supports both 16-bit and CARDBus PC CARDs, powered at 5 V or 3.3 V, as required.

Features
The PCI1410 supports the following features:
• Ability to wake from D3hot and D3cold
• Fully compatible with the Intel 430TX (Mobile Triton II) chipset
• A 144-terminal low-profile QFP (PGE), 144-terminal
   MicroStar BGA™ ball grid array (GGU) package, or
   209-terminal MicroStar BGA (GHK) package
• 3.3-V core logic with universal PCI interfaces compatible
   with 3.3-V and 5-V PCI signaling environments
• Mix-and-match 5-V/3.3-V 16-bit PC CARDs and 3.3-V CARDBus CARDs
• Single PC CARD or CARDBus slot with hot insertion and removal
• Burst transfers to maximize data throughput
   on the PCI bus and the CARDBus bus
• Parallel PCI interrupts, parallel ISA IRQ
   and parallel PCI interrupts, serial ISA IRQ with parallel PCI
   interrupts, and serial ISA IRQ and PCI interrupts
• Serial EEPROM interface for loading subsystem ID and subsystem vendor ID
• Pipelined architecture allows greater
   than 130-Mbps sustained throughput from CARDBus to PCI and from
   PCI to CARDBus
• Interface to parallel single-slot
   PC CARD power interface switches like the TI TPS2211
• Up to five general-purpose I/Os
• Programmable output select for CLKRUN
• Five PCI memory windows and two I/O windows
   available to the 16-bit PC CARD socket
• Two I/O windows and two memory windows available to the CARDBus socket
• Exchangeable CARD architecture (ExCA)
   compatible registers are mapped in memory and I/O space
• Intel 82365SL-DF and 82365SL register compatible
• Distributed DMA (DDMA) and PC/PCI DMA
• 16-Bit DMA on the PC CARD socket
• Ring indicate, SUSPEND, PCI CLKRUN, and CARDBus CCLKRUN
• Socket activity LED pins
PCI bus lock (LOCK)
• Advanced submicron, low-power CMOS technology
• Internal ring oscillator

Part Name(s) : TPS2202AI TPS2202AIDF TPS2202AIDB TPS2202AIDBLE TPS2202AIDFLE Texas-Instruments
Texas Instruments
Description : DUAL-SLOT PC CARD POWER-INTERFACE SWITCH WITH RESET FOR SERIAL PCMCIA CONTROLLER View

description
The TPS2202AI PC CARD power-interface switch provides an integrated power-management solution for two PC CARDs. All of the discrete power MOSFETs, a logic section, current limiting, thermal protection, and power-good reporting for PC CARD control are combined on a single integrated circuit (IC), using the Texas Instruments LinBiCMOS process. The circuit allows the distribution of 3.3-V, 5-V, and/or 12-V CARD power by means of the P2C (PCMCIA Peripheral-Control) Texas Instruments nonproprietary serial interface. The current-limiting feature eliminates the need for fuses, which reduces component count and improves reliability. Current-limit reporting can help the user isolate a system fault to a specific CARD.

● Fully Integrated VCC and Vpp Switching for Dual-Slot PC CARD™ Interface
● P2C™ 3-Lead Serial Interface Compatible With CARDBus™ CONTROLLERS
● Meets PC CARD Standards 
● RESET Allows System Initialization of PC CARDs
● 12-V Supply Can Be Disabled Except During 12-V Flash Programming
● Short-Circuit and Thermal Protection 
● Space-Saving 30-Pin SSOP (DB) Package
● Compatible With 3.3-V, 5-V and 12-V PC CARDs
● Power Saving IDD = 83 µA Typ, IQ = 1 µA 
● Low rDS(on) (160-mΩ VCC Switch)
● Break-Before-Make Switching

Part Name(s) : NS0019 BOTHHAND
Bothhand USA, LP.
Description : 10/100 PC CARD LAN MAGNETICS SOLUTIONS View

10/100 PC CARD LAN MAGNETICS SOLUTIONS

Feature
● Half port and single port designs for maximum layout flexibility.
● Low profile packages from 0.094 Inch(2.39mm) to 0.078 Inch(1.98mm) for PC CARD and CARD bus applications.
● TX OCL 350uH min. with 8mA Bias.
● Operation temperature range: 0℃ to +70℃.
● Storage temperature range: -25℃ to +125℃.

1

2345678910 Next

All Rights Reserved © datasheetbank.com 2014 - 2019 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]