datasheetbank_Logo    Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name  

P/N + Description + Content Search

Search Words :

Part Name(s) : ST6215L ST6215LB1 ST6215LM1 ST6225L ST-Microelectronics
STMicroelectronics
Description : LOW VOLTAGE 8-BIT ROM MCUS WITH A/D CONVERTER AND 28 PINS

INTRODUCTION
The ST6215L/25L are LOW VOLTAGE mask programmed ROM version of ST62T15C,T25C OTP devices.
They offer the same functionality as OTP devices, selecting as ROM options the options defined in the programmable option byte of the OTP version, WITH the exception of the LVD Reset that is not available.

■ 2.4 to 3.9V Supply Operating Range
■ 4 MHz Maximum Clock Frequency
■ 0 to +70°C Operating Temperature Range
■ Run, Wait and Stop Modes
■ 5 Interrupt Vectors
■ Look-up Table capability in Program Memory
■ Data Storage in Program Memory: User selectable size
■ Data RAM: 64bytes
■ 20 I/O PINS, fully programmable as:
    – Input WITH pull-up resistor
    – Input WITHout pull-up resistor
    – Input WITH interrupt generation
    – Open-drain or push-pull output
    – Analog Input
■ 8 I/O lines can sink up to 12mA to drive LEDs
8-BIT Timer/Counter WITH 7-bit programmable prescaler
■ Digital Watchdog
8-BIT A/D Converter WITH 16 analog inputs
■ On-chip Clock oscillator can be driven by Quartz Crystal Ceramic resonator or RC network
■ Power-on Reset
■ One external Non-Maskable Interrupt
■ ST626x-EMU2 Emulation and Development System (connects to an MS-DOS PC via an RS232 serial line)

View
Part Name(s) : ST6200L ST6200LB1_97 ST6200LM1_97 ST6201L ST6201LB1_97 ST6201LM1_97 ST6203L ST6203LB1_97 ST6203LM1_97 ST6200LB1/XXX ST6200LM1/XXX ST6201LB1/XXX ST6201LM1/XXX ST6203LB1/XXX ST6203LM1/XXX ST-Microelectronics
STMicroelectronics
Description : LOW VOLTAGE 8-BIT ROM MCUS WITH A/D CONVERTER,AND 16 PINS

GENERAL DESCRIPTION
INTRODUCTION
The ST6200L/01L and 03L are LOW VOLTAGE mask programmed ROM version of ST62T00C,T01C and T03C OTP devices.
They offer the same functionality as OTP devices, selecting as ROM options the options defined in the programmable option byte of the OTP version, WITH the exception of the LVD Reset and the OSG that are not available.

■ 2.4 to 3.9V Supply Operating Range
■ 4 MHz Maximum Clock Frequency
■ 0 to +70°C Operating Temperature Range
■ Run, Wait and Stop Modes
■ 5 Interrupt Vectors
■ Look-up Table capability in Program Memory
■ Data Storage in Program Memory:
   User selectable size
■ Data RAM: 64bytes
■ 9 I/O PINS, fully programmable as:
   – Input WITH pull-up resistor
   – Input WITHout pull-up resistor
   – Input WITH interrupt generation
   – Open-drain or push-pull output
   – Analog Input (except ST6203L)
■ 3 I/O lines can sink up to 12mA to drive LEDs
8-BIT Timer/Counter WITH 7-bit programmable prescaler
■ Digital Watchdog
8-BIT A/D Converter WITH up to 4 analog inputs
■ On-chip Clock oscillator can be driven by Quartz
   Crystal Ceramic resonator or RC network
■ Power-on Reset
■ One external Non-Maskable Interrupt
■ ST626x-EMU2 Emulation and Development
   System (connects to an MS-DOS PC via an RS232 serial line)

View
Part Name(s) : ST6208L ST6208LB1 ST6208LM1 ST6209L ST6209LB1 ST6209LM1 ST6210L ST6210LB1 ST6210LM1 ST6220L ST6220LB1 ST6220LM1 ST62T08L ST62T09L ST62T10L ST62T20L ST6208LB1/XXX ST6208LM1/XXX ST6209LB1/XXX ST6209LM1/XXX ST6210LB1/XXX ST6210LM1/XXX ST6220LB1/XXX ST6220LM1/XXX STMICROELECTRONICS
STMicroelectronics
Description : LOW VOLTAGE 8-BIT ROM MCUS WITH A/D CONVERTER AND 20 PINS

 INTRODUCTION
The ST6208L/09L/10L/20L are LOW VOLTAGE mask programmed ROM version of ST62T08C/T09C/ T10C/T20C OTP devices.
They offer the same functionality as OTP devices, selecting as ROM options the options defined in the programmable option byte of the OTP version, WITH the exception of the LVD Reset that is not available.

■ 2.4 to 3.9V Supply Operating Range
■ 4 MHz Maximum Clock Frequency
■ 0 to +70°C Operating Temperature Range
■ Run, Wait and Stop Modes
■ 5 Interrupt Vectors
■ Look-up Table capability in Program Memory
■ Data Storage in Program Memory: User selectable size
■ Data RAM: 64bytes
■ 12 I/O PINS, fully programmable as:
    – Input WITH pull-up resistor
    – Input WITHout pull-up resistor
    – Input WITH interrupt generation
    – Open-drain or push-pull output
    – Analog Input (except ST6208L)
■ 4 I/O lines can sink up to 12mA to drive LEDs
8-BIT Timer/Counter WITH 7-bit programmable prescaler
■ Digital Watchdog
8-BIT A/D Converter WITH 8 analog inputs
■ On-chip Clock oscillator can be driven by Quartz Crystal Ceramic resonator or RC network
■ Power-on Reset
■ One external Non-Maskable Interrupt
■ ST626x-EMU2 Emulation and Development System (connects to an MS-DOS PC via an RS232 serial line)

View
Part Name(s) : ST6252B ST6252BB1 ST6252BB3 ST6252BB6 ST6252BM1 ST6252BM3 ST6252BM6 ST-Microelectronics
STMicroelectronics
Description : 8-BIT ROM MCUS WITH A/D CONVERTER, AUTO-RELOAD TIMER, ROM AND EEPROM

GENERAL DESCRIPTION
INTRODUCTION
The ST6252B and ST6262B are mask programmed ROM version of ST62T52B and ST62T62B OTP devices.
They offer the same functionality as OTP devices, selecting as ROM options the options defined in the programmable option byte of the OTP version.

■ 3.0 to 6.0V Supply Operating Range
■ 8 MHz Maximum Clock Frequency
■ -40 to +125°C Operating Temperature Range
■ Run, Wait and Stop Modes
■ 5 Interrupt Vectors
■ Look-up Table capability in Program Memory
■ Data Storage in Program Memory: User selectable size
■ Data RAM: 128 bytes
■ Data EEPROM: 64 bytes (none on ST62T52B)
■ 9 I/O PINS, fully programmable as:
   – Input WITH pull-up resistor
   – Input WITHout pull-up resistor
   – Input WITH interrupt generation
   – Open-drain or push-pull output
   – Analog Input
■ 5 I/O lines can sink up to 20mA to drive LEDs or TRIACs directly
8-BIT Timer/Counter WITH 7-bit programmable prescaler
8-BIT Auto-reload Timer WITH 7-bit programmable prescaler (AR Timer)
■ Digital Watchdog
8-BIT A/D Converter WITH 4 analog inputs
■ On-chip Clock oscillator can be driven by Quartz Crystal Ceramic resonator or RC network
■ User configurable Power-on Reset
■ One external Non-Maskable Interrupt
■ ST626x-EMU2 Emulation and Development System (connects to an MS-DOS PC via a parallel port)

 

View
Part Name(s) : XA-S3 PXAS30KBA PXAS33KBA PXAS37KBA PXAS30KBBE PXAS33KBBE PXAS37KBBE PXAS30KFA PXAS33KFA PXAS37KFA PXAS30KFBE PXAS33KFBE PXAS37KFBE Philips
Philips Electronics
Description : XA 16-bit microcontroller 32 K/1 K OTP/ROM/ROMless, 8-channel 8-BIT A/D, LOW VOLTAGE (2.7 V–5.5 V), I2C, 2 UARTs, 16 MB address range

GENERAL DESCRIPTION
The XA-S3 device is a member of Philips Semiconductors’ XA (eXtended Architecture) family of high performance 16-bit single-chip microcontrollers.
The XA-S3 device combines many powerful peripherals on one
chip. WITH its high performance A/D converter, timers/counters, watchdog, Programmable Counter Array (PCA), I2C interface, dual UARTs, and multiple general purpose I/O ports, it is suited for general multipurpose high performance embedded control functions.

Specific features of the XA-S3
• 2.7 V to 5.5 V operation.
• 32 K bytes of on-chip EPROM/ROM program memory.
• 1024 bytes of on-chip data RAM.
• Supports off-chip addressing up to 16 megabytes (24 address
   lines). A clock output reference is added to simplify external bus
   interfacing.
• High performance 8-channel 8-BIT A/D converter WITH automatic
   channel scan and repeated read functions. Completes a
   conversion in 4.46 microseconds at 30 MHz. Alternate operating
   mode alLOWs 10-bit conversion results.
• Three standard counter/timers WITH enhanced features. All timers
   have a toggle output capability.
• Watchdog timer.
• 5-channel 16-bit Programmable Counter Array (PCA).
• I2C-bus serial I/O port WITH byte-oriented master and slave functions.
• Two enhanced UARTs WITH independent baud rates.
• Seven software interrupts.
• Active LOW reset output pin indicates all reset occurrences
   (external reset, watchdog reset and the RESET instruction). A
   reset source register alLOWs program determination of the cause of
   the most recent reset.
• 50 I/O PINS, each WITH 4 programmable output configurations.
• 30 MHz operating frequency at 2.7–5.5 V VDD.
• Power saving operating modes: Idle and Power-down. Wake-up
   fROM power-down via an external interrupt is supported.
• 68-pin PLCC and 80-pin PQFP packages.

View
Part Name(s) : M6M80041P M6M80041FP Mitsubishi
MITSUBISHI ELECTRIC
Description : 4096-BIT (256-WORD BY 16-BIT) ELECTRICALLY ERASABLE AND PROGRAMMABLE ROM

4096-BIT (256-WORD BY 16-BIT) ELECTRICALLY ERASABLE AND PROGRAMMABLE ROM

View
Part Name(s) : PXAS30KBA PXAS30KBBE PXAS30KFA PXAS30KFBE PXAS33KBA PXAS33KBBE PXAS33KFA PXAS33KFBE PXAS37KBA PXAS37KBBE PXAS37KFA PXAS37KFBE XA-S3 PXAS30KBA,512 PXAS30KBBE,557 PXAS30KFA,512 NXP
NXP Semiconductors.
Description : XA 16-bit microcontroller 32 K/1 K OTP/ROM/ROMless, 8-channel 8-BIT A/D, LOW VOLTAGE (2.7 V–5.5 V), I2C, 2 UARTs, 16 MB address range

GENERAL DESCRIPTION
The XA-S3 device is a member of NXP Semiconductors’ XA (eXtended Architecture) family of high performance 16-bit single-chip microcontrollers.
The XA-S3 device combines many powerful peripherals on one chip. WITH its high performance A/D converter, timers/counters, watchdog, Programmable Counter Array (PCA), I2C interface, dual UARTs, and multiple general purpose I/O ports, it is suited for general multipurpose high performance embedded control functions.

Specific features of the XA-S3
• 2.7 V to 5.5 V operation.
• 32 K bytes of on-chip EPROM/ROM program memory.
• 1024 bytes of on-chip data RAM.
• Supports off-chip addressing up to 16 megabytes (24 address
   lines). A clock output reference is added to simplify external bus
   interfacing.
• High performance 8-channel 8-BIT A/D converter WITH automatic
   channel scan and repeated read functions. Completes a
   conversion in 4.46 microseconds at 30 MHz. Alternate operating
   mode alLOWs 10-bit conversion results.
• Three standard counter/timers WITH enhanced features. All timers have a toggle output capability.
• Watchdog timer.
• 5-channel 16-bit Programmable Counter Array (PCA).
• I2C-bus serial I/O port WITH byte-oriented master and slave functions.
• Two enhanced UARTs WITH independent baud rates.
• Seven software interrupts.
• Active LOW reset output pin indicates all reset occurrences
   (external reset, watchdog reset and the RESET instruction). A
   reset source register alLOWs program determination of the cause
   of the most recent reset.
• 50 I/O PINS, each WITH four programmable output configurations.
• 30 MHz operating frequency at 2.7 V to 5.5 V VDD.
• Power saving operating modes: Idle and Power-down. Wake-up
   fROM power-down via an external interrupt is supported.
• 68-pin PLCC and 80-pin PQFP packages.

View
Part Name(s) : ST9293 ST9293J7 ST9293J5 ST9293J3 ST9293J1 ST-Microelectronics
STMicroelectronics
Description : 48K ROM HCMOS MCUS WITH ON SCREEN DISPLAY AND A/D CONVERTER

GENERAL DESCRIPTION
The ST9293 is a ROM member of the ST9 family of microcontrollers, completely developed and produced by SGS-THOMSON Microelectronics using a proprietary n-well HCMOS process.
The ROM parts are fully compatible WITH their EPROM versions, which may be used for the prototyping and pre-production phases of development, and can be configured as standalone microcontrollers WITH 48K/32K/24K/16 bytes of on chip ROM.
The nucleus of the ST9293 is the advanced Core which includes the Central Processing Unit (CPU), the Register File, a 16-bit Timer/Watchdog WITH 8-BIT Prescaler, a Serial Peripheral Interface support ing S-bus, I2C-bus and IM-bus Interface, plus two 8-BIT I/O ports. The Core has independent memory and register buses alLOWing a high degree of pipelining to add to the efficiency of the code execution speed of the extensive instruction set.The powerful I/O capabilities demanded by microcontroller applications are fulfilled by the ST9293 WITH up to 31/41 I/O lines dedicated to digital Input/Output.
These lines are grouped into up to six I/O Ports and can be configured on a bit basis under software control to provide timing, status signals, timer inputs and outputs, analog inputs, external interrupts and serial or parallel I/O.

■ Register oriented 8/16 bit CORE WITH RUN, WFI and HALT modes
■ Minimum instruction cycle time: 500ns (12MHz internal)
16 to 48K bytes of ROM,
   256 to 768 bytes of RAM,
   224 general purpose registers available as RAM,
   accumulators or index registers (Register File)

  
■ 42-lead Shrink DIP package
■ Interrupt handler and Serial Peripheral Interface as standard features
■ 31 fully programmable I/O PINS
■ 34 character x15 rows software programmable
   On Screen Display module WITH colour, italic, underline, flash, transparent and
   fringe attribute options
16 bit Timer WITH 8 bit Prescaler, able to be used as a Watchdog Timer
16-bit programmable Slice Timer WITH 8-BIT pres caler

■ 4 channel Analog to Digital Converter, WITH integral sample and hold,
   fast 5.75µs conversion time, 6-bit guaranteed resolution
■ Rich Instruction Set and 14 Addressing modes
■ Division-by-Zero trap generation
■ Versatile Development tools, including assembler,
   linker, C-compiler, archiver, graphic oriented debugger and hardware emulators
■ Real Time Operating System
■ Windowed EPROM parts available for prototyping and pre-production development phases

View
Part Name(s) : M5M27C202JK-12I M5M27C202JK-15I M5M27C202K-12I M5M27C202K-15I Mitsubishi
MITSUBISHI ELECTRIC
Description : 2097152-BIT(131072-WORD BY 16-BIT) CMOS ERASABLE AND ELECTRICALLY REPROGRAMMABLE ROM

2097152-BIT(131072-WORD BY 16-BIT) CMOS ERASABLE AND ELECTRICALLY REPROGRAMMABLE ROM

View
Part Name(s) : P80C31 Philips
Philips Electronics
Description : 80C51 8-BIT microcontroller family 4K/128 OTP/ROM/ROMless LOW VOLTAGE (2.7V–5.5V), LOW power, high speed (33 MHz)

DESCRIPTION
The Philips 8XC51/31 is a high-performance static 80C51 design fabricated WITH Philips high-density CMOS technology WITH operation fROM 2.7V to 5.5V.

FEATURES
•8051 Central Processing Unit
–4k ×8 ROM (80C51)
–128 ×8 RAM
–Three 16-bit counter/timers
–Boolean processor
–Full static operation
LOW VOLTAGE (2.7V to 5.5V@ 16MHz) operation
•Memory addressing capability
–64k ROM and 64k RAM
•Power control modes:
–Clock can be stopped and resumed
–Idle mode
–Power-down mode
•CMOS and TTL compatible
•TWO speed ranges at VCC= 5V
–0 to 16MHz
–0 to 33MHz
•Three package styles
•Extended temperature ranges
•Dual Data Pointers
•Security bits:
ROM (2 bits)
–OTP/EPROM (3 bits)
•Encryption array—64 bytes
•4 level priority interrupt
•6 interrupt sources
•Four 8-BIT I/O ports
•Full–duplex enhanced UART
–Framing error detection
–Automatic address recognition
•Programmable clock out
•Asynchronous port reset
LOW EMI (inhibit ALE)
•Wake-up fROM Power Down by an external interrupt (8XC51)

View

1

2345678910 Next

 

All Rights Reserved © datasheetbank.com 2014 - 2019 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]