datasheetbank_Logo    Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name  

P/N + Description + Content Search

Search Words :

Part Name(s) : ST92F150CV1T3 ST-Microelectronics
STMicroelectronics
Description : 8/16-BIT SINGLE VOLTAGE FLASH MCU FAMILY WITH RAM, E3 TM(EMULATED EEPROM), CAN 2.0B AND J1850 BLPD

GENERAL DESCRIPTION
INTRODUCTION
The ST92124-Auto/150-Auto/250-Auto microcontroller is developed and manufactured by STMicroelectronics using a proprietary n-well HCMOS process. Its performance derives from the use of a flexible 256-register progRAMming model for ultrafast context switching and real-time event response. The intelligent on-chip peripherals offload the ST9 core from I/O and data management processing tasks allowing critical application tasks to get the maximum use of core resources. The new-generation ST9 MCU devices now also support low power consumption and low VOLTAGE operation for power-efficient and low-cost embedded systems.

■ Memories
    – Internal Memory: SINGLE VOLTAGE FLASH up to 256 Kbytes, RAM up to 8Kbytes, 1K byte E3 TM (EMULATED EEPROM)
    – In-Application ProgRAMming (IAP)
    – 224 general purpose registers (register file) available as RAM, accumulators or index pointers
■ Clock, Reset and Supply Management
    – Register-oriented 8/16 bit CORE WITH RUN, WFI, SLOW, HALT and STOP modes
    – 0-24 MHz Operation (Int. Clock), 4.5-5.5 V range
    – PLL Clock Generator (3-5 MHz crystal)
    – Minimum instruction time: 83 ns (24 MHz int. clock)
■ Up to 80 I/O pins
■ Interrupt Management
    – 4 external fast interrupts + 1 NMI
    – Up to 16 pins progRAMmable as wake-up or additional external interrupt WITH multi-level interrupt handler
■ DMA controller for reduced processor overhead
■ Timers
    – 16-bit Timer WITH 8-bit Prescaler, and Watchdog Timer (activated by software or by hardware)
    – 16-bit Standard Timer that CAN be used to generate a time base independent of PLL Clock Generator
    – Two 16-bit independent Extended Function Timers (EFTs) WITH Prescaler, up to two Input Captures and up to two Output Compares
    – Two 16-bit Multifunction Timers, WITH Prescaler, up to two Input Captures and up to two Output Compares
■ Communication Interfaces
    – Serial Peripheral Interface (SPI) WITH Selectable Master/Slave mode
    – One Multiprotocol Serial Communications Interface WITH asynchronous and synchronous capabilities
    – One asynchronous Serial Communications Interface WITH 13-bit LIN Synch Break generation capability
    – J1850 Byte Level Protocol Decoder (JBLPD)
    – Up to two full I²C multiple Master/Slave Interfaces supporting Access Bus
    – Up to two CAN 2.0B Active interfaces
■ Analog peripheral (low current coupling)
    – 10-bit A/D Converter WITH up to 16 robust input channels
■ Development Tools
    – Free High performance Development environment (IDE) based on Visual Debugger, Assembler, Linker, and C-Compiler; Real Time Operating System (OSEK OS, CMX) and CAN drivers
    – Hardware Emulator and FLASH ProgRAMming Board for development and ISP FLASHer for production

View
Part Name(s) : ST92F120JR1T ST92F120JR6T ST92F120JR9T ST92F120JV1Q ST92F120JV6Q ST92F120JV9Q ST92F120R1T ST92F120R6T ST92F120R9T ST92F120V1Q ST92F120V6Q ST92F120V9Q ST-Microelectronics
STMicroelectronics
Description : 8/16-BIT FLASH MCU FAMILY WITH RAM, EEPROM AND J1850 BLPD

The ST92F120 microcontroller is developed and manufactured by STMicroelectronics using a proprietary n-well HCMOS process. Its performance derives from the use of a flexible 256-register progRAMming model for ultra-fast context switching and real-time event response. The intelligent on chip peripherals offload the ST9 core from I/O and data management processing tasks allowing critical application tasks to get the maximum use of core resources. The new-generation ST9 MCU devices now also support low power consumption and low VOLTAGE operation for power-efficient and low-cost embedded systems.

View
Part Name(s) : ST7250 ST7250A6 ST7250B4 ST-Microelectronics
STMicroelectronics
Description : 8-BIT MCU FOR CAN WITH 32K ROM, 1K RAM, EEPROM, ADC, WDG, PWM/BRM, 2 TIMERS, SPI AND SCI INTERFACES

8-BIT MCU FOR CAN WITH 32K ROM, 1K RAM, EEPROM, ADC, WDG, PWM/BRM, 2 TIMERS, SPI AND SCI INTERFACES

View
Part Name(s) : HT66F20 HT66F30 HT66F40 HT66F50 HT66F60 HT66FU30 HT66FU40 HT66FU50 HT66FU60 Holtek
Holtek Semiconductor
Description : Enhanced A/D FLASH Type MCU 8-Bit MCU WITH EEPROM

General Description
The HT66FXX series of devices are FLASH Memory A/D type 8-bit high performance RISC architecture microcontrollers. Offering users the convenience of FLASH Memory multi-progRAMming features, these devices also include a wide range of functions and features. Other memory includes an area of RAM Data Memory as well as an area of EEPROM memory for storage of non-volatile data such as serial numbers, calibration data etc.

View
Part Name(s) : ST10F272 ST10F272Z2 ST10F272Z2Q3 ST10F272Z2T3 ST-Microelectronics
STMicroelectronics
Description : 16-bit MCU WITH 256 Kbyte FLASH memory and 20 Kbyte RAM

Introduction
The ST10F272 device is a derivative of the STMicroelectronics ST10 FAMILY of 16-bit SINGLE chip CMOS microcontrollers.
The ST10F272 combines high CPU performance (up to 32 million instructions per second) WITH high peripheral functionality and enhanced I/O-capabilities. It also provides on-chip high-speed SINGLE VOLTAGE FLASH memory, on-chip high-speed RAM, and clock generation via PLL.
ST10F272 is processed in 0.18µm CMOS technology. The MCU core and the logic is supplied WITH a 5V to 1.8V on-chip VOLTAGE regulator. The part is supplied WITH a SINGLE 5V ly and I/Os work at 5V.

Features
■ 16-bit CPU WITH DSP functions
   – 31.25ns instruction cycle time at 64MHz max CPU clock
   – Multiply/accumulate unit (MAC) 16 x 16-bit multiplication, 40-bit accumulator
   – Enhanced boolean bit manipulations
   – SINGLE-cycle context switching support
■ On-chip memories
   – 256 Kbyte FLASH memory (32-bit fetch)
   – SINGLE VOLTAGE FLASH memories WITH erase/progRAM controller and 100K erasing/progRAMming cycles.
   – Up to 16 Mbyte linear address space for code and data (5 Mbytes WITH CAN or I2C)
   – 2 Kbyte internal RAM (IRAM)
   – 18 Kbyte extension RAM (XRAM)
   – ProgRAMmable external bus configuration & characteristics for different address ranges
   – Five progRAMmable chip-select signals
   – Hold-acknowledge bus arbitration support
■ Interrupt
   – 8-channel peripheral event controller for SINGLE cycle interrupt driven data transfer
   – 16-priority-level interrupt system WITH 56 sources, sampling rate down to 15.6ns
■ Timers
   – Two multi-functional general purpose timer units WITH 5 timers
■ Two 16-channel capture / compare units
■ 4-channel PWM unit + 4-channel XPWM
■ A/D converter
   – 24-channel 10-bit
   – 3 µs minimum conversion time
■ Serial channels
   – Two synch. / asynch. serial channels
   – Two high-speed synchronous channels
   – One I2C standard interface
■ 2 CAN 2.0B interfaces operating on 1 or 2 CAN busses (64 or 2x32 message, C-CAN version)
■ Fail-safe protection
   – ProgRAMmable watchdog timer
   – Oscillator watchdog
■ On-chip bootstrap loader
■ Clock generation
   – On-chip PLL WITH 4 to 8 MHz oscillator
   – Direct or prescaled clock input
■ Real time clock and 32 kHz on-chip oscillator
■ Up to 111 general purpose I/O lines
   – Individually progRAMmable as input, output or special function
   – ProgRAMmable threshold (hysteresis)
■ Idle, power down and stand-by modes
SINGLE VOLTAGE supply: 5V ±10%

 

View
Part Name(s) : ST10F273 ST10F273Z4Q3 ST10F273Z4T3 ST-Microelectronics
STMicroelectronics
Description : 16-bit MCU WITH 512 Kbyte FLASH memory and 36 Kbyte RAM

Introduction
The ST10F273 device is a derivative of the STMicroelectronics ST10 FAMILY of 16-bit SINGLE chip CMOS microcontrollers.
The ST10F273 combines high CPU performance (up to 32 million instructions per second) WITH high peripheral functionality and enhanced I/O-capabilities. It also provides on-chip high-speed SINGLE VOLTAGE FLASH memory, on-chip high-speed RAM, and clock generation via PLL.
ST10F273 is processed in 0.18mm CMOS technology. The MCU core and the logic is supplied WITH a 5 V to 1.8 V on-chip VOLTAGE regulator. The part is supplied WITH a SINGLE 5 V supply and I/Os work at 5 V.

Features
■ High performance 16-bit CPU WITH DSP functions
– 31.25ns instruction cycle time at 64 MHz max CPU clock
– Multiply/accumulate unit (MAC) 16 x 16-bit multiplication, 40-bit accumulator
– Enhanced boolean bit manipulations
SINGLE-cycle context switching support
■ Memory organization
– 512 Kbyte on-chip FLASH memory SINGLE VOLTAGE WITH erase/progRAM controller (full performance, 32-bit fetch)
– 100K erasing/progRAMming cycles.
– Up to 16 Mbyte linear address space for code and data (5 Mbytes WITH CAN or I2C)
– 2 Kbyte on-chip internal RAM (IRAM)
– 34 Kbyte on-chip extension RAM (XRAM)
– ProgRAMmable external bus configuration & characteristics for different address ranges
– 5 progRAMmable chip-select signals
– Hold-acknowledge bus arbitration support
■ Interrupt
– 8-channel peripheral event controller for SINGLE cycle interrupt driven data transfer
– 16-priority-level interrupt system WITH 56 sources, sampling rate down to 15.6ns
■ Timers
– 2 multifunctional general purpose timer units WITH 5 timers
■ Two 16-channel capture / compare units
■ 4-channel PWM unit + 4-channel XPWM
■ A/D Converter
– 24-channel 10-bit
– 3µs Minimum conversion time
■ Serial channels
– 2 synch. / asynch. serial channels
– 2 high-speed synchronous channels
– I2C standard interface
■ 2 CAN 2.0B interfaces operating on 1 or 2 CAN busses (64 or 2x32 messages, C-CAN version)
■ Fail-safe protection
– ProgRAMmable watchdog timer
– Oscillator watchdog
■ On-chip bootstrap loader
■ Clock generation
– On-chip PLL and 4 to 12 MHz oscillator
– Direct or prescaled clock input
■ Real time clock and 32kHz on-chip oscillator
■ Up to 111 general purpose I/O lines
– Individually progRAMmable as input, output or special function
– ProgRAMmable threshold (hysteresis)
■ Idle, power down and stand-by modes
SINGLE VOLTAGE supply: 5 V ±10%.

View
Part Name(s) : XA-G39 PXAG39KBA Philips
Philips Electronics
Description : XA 16-bit microcontroller FAMILY 32K FLASH/1K RAM, watchdog, 2 UARTs

GENERAL DESCRIPTION
The XA-G39 is a member of Philips’ 80C51 XA (eXtended Architecture) FAMILY of high performance 16-bit SINGLE-chip microcontrollers.

FEATURES
• 32 kbytes of on-chip FLASH progRAM memory WITH In-System ProgRAMming capability
• Three FLASH blocks = two 8 kbyte blocks and one 16 kbyte block
• Provides FLASH solution for XA-G37 (OTP) designs
SINGLE supply VOLTAGE In-System ProgRAMming (ISP) of the FLASH memory (VPP = VDD, or VPP = 12 V if desired)
• Boot ROM contains low level FLASH progRAMming routines for In-Application ProgRAMming and a default serial loader using the UART
• 1024 bytes of on-chip data RAM
• Supports off-chip progRAM and data addressing up to 1 megabyte (20 address lines)
• Three standard counter/timers WITH enhanced features (same as XA-G3 T0, T1, and T2). All timers have a toggle output capability
• Watchdog timer
• Two enhanced UARTs WITH independent baud rates
• Seven software interrupts
• Four 8-bit I/O ports, WITH 4 progRAMmable output configurations for each pin
• 30 MHz operating frequency at 5 V
• Power saving operating modes: Idle and Power-Down. Wake-Up from power-down via an external interrupt is supported.
• 44-pin PLCC package

View
Part Name(s) : ST10F271 ST-Microelectronics
STMicroelectronics
Description : 16-bit MCU WITH 128 Kbyte FLASH memory and 12 Kbyte RAM

Introduction
The ST10F271 device is a derivative of the STMicroelectronics ST10 FAMILY of 16-bit SINGLEchip CMOS microcontrollers.
The ST10F271 combines high CPU performance (up to 32 million instructions per second) WITH high peripheral functionality and enhanced I/O-capabilities. It also provides on-chip high-speed SINGLE VOLTAGE FLASH memory, on-chip high-speed RAM, and clock generation via PLL.

Features
■ 16-bit CPU WITH DSP functions
– 31.25ns instruction cycle time at 64MHz max CPU clock
– Multiply/accumulate unit (MAC) 16 x 16-bit multiplication, 40-bit accumulator
– Enhanced boolean bit manipulations
SINGLE-cycle context switching support
■ On-chip memories
– 128 Kbyte FLASH memory (32-bit fetch)
SINGLE VOLTAGE FLASH memories WITH erase/progRAM controller and 100K erasing/progRAMming cycles.
– Up to 16 Mbyte linear address space for code and data (5 Mbytes WITH CAN or I2C)
– 2 Kbyte internal RAM (IRAM)
– 10 Kbyte extension RAM (XRAM)
– ProgRAMmable external bus configuration & characteristics for different address ranges
– Five progRAMmable chip-select signals
– Hold-acknowledge bus arbitration support
■ Interrupt
– 8-channel peripheral event controller for SINGLE cycle interrupt driven data transfer
– 16-priority-level interrupt system WITH 56 sources, sampling rate down to 15.6ns
■ Timers
– Two multi-functional general purpose timer units WITH 5 timers
■ Two 16-channel capture / compare units
■ 4-channel PWM unit + 4-channel XPWM
■ A/D converter
– 24-channel 10-bit
–3µs minimum conversion time
■ Serial channels
– Two synch. / asynch. serial channels
– Two high-speed synchronous channels
–One I2C standard interface
■ 2 CAN 2.0B interfaces operating on 1 or 2 CAN busses (64 or 2x32 message, C-CAN version)
■ Fail-safe protection
– ProgRAMmable watchdog timer
– Oscillator watchdog
■ On-chip bootstrap loader
■ Clock generation
– On-chip PLL WITH 4 to 8 MHz oscillator
– Direct or prescaled clock input
■ Real time clock and 32kHz on-chip oscillator
■ Up to 111 general purpose I/O lines
– Individually progRAMmable as input, output or special function
– ProgRAMmable threshold (hysteresis)
■ Idle, power down and stand-by modes
SINGLE VOLTAGE supply: 5V ±10%

View
Part Name(s) : ST10F271Z1 ST10F271Z1Q3 ST10F271Z1T3 ST-Microelectronics
STMicroelectronics
Description : 16-bit MCU WITH 128 Kbyte FLASH memory and 12 Kbyte RAM

Introduction
The ST10F271Z1 device is a derivative of the STMicroelectronics ST10 FAMILY of 16-bit SINGLE-chip CMOS microcontrollers.
The ST10F271Z1 combines high CPU performance (up to 32million instructions per second) WITH high peripheral functionality and enhanced I/O-capabilities. It also provides on chip high-speed SINGLE VOLTAGE FLASH memory, on-chip high-speed RAM, and clock generation via PLL.

Features
■ 16-bit CPU WITH DSP functions
– 31.25ns instruction cycle time at 64MHz max CPU clock
– Multiply/accumulate unit (MAC) 16 x 16-bit multiplication, 40-bit accumulator
– Enhanced boolean bit manipulations
SINGLE-cycle context switching support
■ On-chip memories
– 128 Kbyte FLASH memory (32-bit fetch)
SINGLE VOLTAGE FLASH memories WITH erase/progRAM controller and 100K erasing/progRAMming cycles.
– Up to 16 Mbyte linear address space for code and data (5 Mbytes WITH CAN or I2C)
– 2 Kbyte internal RAM (IRAM)
– 10 Kbyte extension RAM (XRAM)
– ProgRAMmable external bus configuration & characteristics for different address ranges
– Five progRAMmable chip-select signals
– Hold-acknowledge bus arbitration support
■ Interrupt
– 8-channel peripheral event controller for SINGLE cycle interrupt driven data transfer
– 16-priority-level interrupt system WITH 56 sources, sampling rate down to 15.6ns
■ Timers
– Two multi-functional general purpose timer units WITH 5 timers
■ Two 16-channel capture / compare units
■ 4-channel PWM unit + 4-channel XPWM
■ A/D converter
– 24-channel 10-bit
–3µs minimum conversion time
■ Serial channels
– Two synch. / asynch. serial channels
– Two high-speed synchronous channels
–One I2C standard interface
■ 2 CAN 2.0B interfaces operating on 1 or 2 CAN busses (64 or 2x32 message, C-CAN version)
■ Fail-safe protection
– ProgRAMmable watchdog timer
– Oscillator watchdog
■ On-chip bootstrap loader
■ Clock generation
– On-chip PLL WITH 4 to 8 MHz oscillator
– Direct or prescaled clock input
■ Real time clock and 32kHz on-chip oscillator
■ Up to 111 general purpose I/O lines
– Individually progRAMmable as input, output or special function
– ProgRAMmable threshold (hysteresis)
■ Idle, power down and stand-by modes
SINGLE VOLTAGE supply: 5V ±10%

View
Part Name(s) : 8S003F3 ST-Microelectronics
STMicroelectronics
Description : V alue line, 16 MHz STM8S 8-bit MCU, 8 Kbytes FLASH, 128 bytes data EEPROM, 10-bit ADC, 3 timers, UART , SPI, I2C

8S003F3 Search -----> STM8S003F3

The STM8S003x value line 8-bit microcontrollers feature 8 Kbytes FLASH progRAM memory, plus integrated true data EEPROM. The STM8S microcontroller FAMILY reference manual (RM0016) refers to devices in this FAMILY as low-density . They provide the following benefits: performance, robustness, and reduced system cost.
Device performance and robustness are ensured by integrated true data EEPROM supporting up to 100000 write/erase cycles, advanced core and peripherals made in a state-of-the art technology , a 16 MHz clock frequency , robust I/Os, independent watchdogs WITH separate clock source, and a clock security system.
The system cost is reduced thanks to high system integration level WITH internal clock oscillators, watchdog and brown-out reset.

View

1

2345678910 Next

 

All Rights Reserved © datasheetbank.com 2014 - 2019 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]