datasheetbank_Logo     Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

P/N + Description + Content Search

Search Words :

Part Name(s) : NM93CS06L NM93CS06LEM8 NM93CS06LEN NM93CS06LM8 NM93CS06LN NM93CS46L NM93CS46LEM8 NM93CS46LEMT8 NM93CS46LEN NM93CS46LM8 NM93CS46LMT8 NM93CS46LN NM93CS56L NM93CS56LEM8 NM93CS56LEMT8 NM93CS56LEN NM93CS56LM8 NM93CS56LMT8 NM93CS56LN NM93CS66L NM93CS66LEM8 NM93CS66LEMT8 NM93CS66LEN NM93CS66LM8 NM93CS66LMT8 National-Semiconductor
National ->Texas Instruments
Description : 256-/1024-/2048-/4096-BIT SERIAL EEPROM WITH EXTENDED VOLTAGE (2.7V TO 5.5V) and Data Protect (MICROWIRETM BUS Interface) View

General Description
The NM93CS06L/CS46L/CS56L/CS66L devices are 256/1024/2048/4096 bits, respectively, of non-volatile electrically erasable memory divided inTO 16/64/128/256 x 16-bit registers (addresses). The NM93CSxxL Family functions in an EXTENDED VOLTAGE operating range, and is fabricated using National SemiconducTOr’s floating gate CMOS technology for high reliability, high endurance and low power consumption.
   
Features
■ Sequential register read
■ Write protection in a user defined section of memory
■ 2.7V TO 5.5V operating range in all modes
■ Typical active current of 200 mA; typical standby
    current of 1 μA
■ No erase required before write
■ Reliable CMOS floating gate technology
■ MICROWIRE compatible SERIAL I/O
■ Self timed write cycle
■ Device status during programming mode
■ 40 year data retention
■ Endurance: 106 data changes
■ Packages Available: 8-pin SO, 8-pin DIP, and 8-pin
    TSSOP
   

Part Name(s) : NM93C06L NM93C06LE NM93C06LEM8 NM93C06LEMT8 NM93C06LEN NM93C06LM8 NM93C06LMT8 NM93C06LN NM93C06LV NM93C06LVM8 NM93C06LVMT8 NM93C06LVN NM93C06LZEM8 NM93C06LZEN NM93C06LZVM8 NM93C06LZVMT8 NM93C46L NM93C46LE NM93C46LEM8 NM93C46LEMT8 NM93C46LEN NM93C46LM8 NM93C46LMT8 NM93C46LN NM93C46LV National-Semiconductor
National ->Texas Instruments
Description : 256-/1024-/2048-/4096-BIT SERIAL EEPROM WITH EXTENDED VOLTAGE (2.7V TO 5.5V)(MICROWIRETM BUS Interface) View

General Description
The NM93C06L/C46L/C56L/C66L devices are 256/1024/2048/4096 bits, respectively, of non-volatile electrically erasable memory divided inTO 16/64/128/256 x 16-bit registers (addresses). The NM93CxxL Family functions in an EXTENDED VOLTAGE operating range, requires only a single power supply and is fabricated using National SemiconducTOr’s floating gate CMOS technology for high reliability, high endurance and low power consumption. These devices are available in both SO and TSSOP packages for small space considerations.

Features
■ 2.7V TO 5.5V operation in all modes
■ Typical active current of 100 mA; Typical standby current of 1 mA
■ No erase required before write
■ Reliable CMOS floating gate technology
■ MICROWIRE compatible SERIAL I/O
■ Self-timed programming cycle
■ Device status during programming mode
■ 40 years data retention
■ Endurance: 106 data changes
■ Packages available: 8-pin SO, 8-pin DIP, and 8-pin TSSOP

 

Part Name(s) : NM93CS06E NM93CS06EM8 NM93CS06EN NM93CS06M NM93CS06M8 NM93CS06MM8 NM93CS06MN NM93CS06N NM93CS46EM8 NM93CS46EN NM93CS46M8 NM93CS46MM8 NM93CS46MN NM93CS46N NM93CS56EM8 NM93CS56EN NM93CS56M8 NM93CS56MM8 NM93CS56MN NM93CS56N NM93CS66E NM93CS66EM8 NM93CS66EN NM93CS66M NM93CS66M8 National-Semiconductor
National ->Texas Instruments
Description : (MICROWIRETM BUS Interface) 256-/1024-/2048-/4096-BIT SERIAL EEPROM WITH Data Protect and Sequential Read View

General Description
The NM93CS06/CS46/CS56/CS66 devices are 256/1024/2048/4096 bits, respectively, of CMOS non-volatile electrically erasable memory divided inTO 16/64/128/256 16-bit registers. Selected registers can be protected against data modification by programming the Protect Register WITH the address of the first register TO be protected against data modification (all registers greater than, or equal TO, the selected address are then protected from further change).
   
Features
■ Write protection in a user defined section of memory
■ Sequential register read
■ Typical active current of 400 mA and standby current of 25 μA
■ No erase required before write
■ Reliable CMOS floating gate technology
■ MICROWIRE compatible SERIAL I/O
■ Self timed write cycle
■ Device status during programming mode
■ 40 year data retention
■ Endurance: 106 data changes
■ 4.5V TO 5.5V operation in all modes of operation
■ Packages available: 8-pin SO, 8-pin DIP
   

Part Name(s) : AT24C01A-10TSI-2.7 AT24C01A-W1.8-1 AT24C01ASC-10WU Atmel
Atmel Corporation
Description : 2-Wire SERIAL EEPROM 1K (128 x 8),2K (256 x 8),4K (512 x 8),8K (1024 x 8),16K (2048 x 8) View

Description
The AT24C01A/02/04/08/16 provides 1024/2048/4096/8192/16384 bits of SERIAL electrically erasable and programmable read only memory (EEPROM) organized as 128/256/512/1024/2048 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low power and low VOLTAGE operation are essential. The AT24C01A/02/04/08/16 is available in space saving 8-pin PDIP,(AT24C01A/02/04/08/16), 8-Pin MSOP (AT24001A/02), 8-Pin TSSOP (AT24C01A/02/04/08/16), and 8-Pin and 14-Pin JEDEC SOIC (AT24C01A/02/04/08/16) packages and is accessed via a 2-wire SERIAL interface. In addition, the entire family is available in 5.0V (4.5V TO 5.5V), 2.7V (2.7V TO 5.5V), 2.5V (2.5V TO 5.5V) and 1.8V (1.8V TO 5.5V) versions.

Features
• Low-VOLTAGE and Standard-VOLTAGE Operation
– 5.0 (VCC = 4.5V TO 5.5V)
– 2.7 (VCC = 2.7V TO 5.5V)
– 2.5 (VCC = 2.5V TO 5.5V)
– 1.8 (VCC = 1.8V TO 5.5V)
• Internally Organized 128 x 8 (1K), 256 x 8 (2K), 512 x 8 (4K),
1024 x 8 (8K) or 2048 x 8 (16K)
• 2-Wire SERIAL Interface
• Schmitt Trigger, Filtered Inputs for Noise Suppression
• Bidirectional Data Transfer ProTOcol
• 100 kHz (1.8V, 2.5V, 2.7V) and 400 kHz (5V) Compatibility
• Write Protect Pin for Hardware Data Protection
• 8-Byte Page (1K, 2K), 16-Byte Page (4K, 8K, 16K) Write Modes
• Partial Page Writes Are Allowed
• Self-Timed Write Cycle (10 ms max)
• High Reliability
– Endurance: 1 Million Write Cycles
– Data Retention: 100 Years
– ESD Protection: >3000V
• AuTOmotive Grade and EXTENDED Temperature Devices Available
• 8-Pin and 14-Pin JEDEC SOIC, 8-Pin PDIP, 8-Pin MSOP, and 8-Pin TSSOP Packages


Part Name(s) : AT25080 AT25160 AT25320 AT25640 Atmel
Atmel Corporation
Description : SPI SERIAL EEPROMs 8K (1024 x 8),16K (2048 x 8),32K (4096 x 8),64K (8192 x 8) View

Description
The AT25080/160/320/640 provides 8192/16384/32768/65536 bits of SERIAL electrically-erasable programmable read only memory (EEPROM) organized as 1024/2048/4096/8192 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-VOLTAGE operation are essential. The AT25080/160/320/640 is available in space saving 8-lead PDIP, 8-lead JEDEC SOIC and 14-lead TSSOP packages

Features
SERIAL Peripheral Interface (SPI) Compatible
• Supports SPI Modes 0 (0,0) and 3 (1,1)
• Low-VOLTAGE and Standard-VOLTAGE Operation
    – 2.7 (VCC = 2.7V TO 5.5V)
    – 1.8 (VCC = 1.8V TO 5.5V)
• 3.0 MHz Clock Rate (5V)
• 32-byte Page Mode
• Block Write Protection
    – Protect 1/4, 1/2, or Entire Array
• Write Protect (WP) Pin and Write Disable Instructions for both Hardware and Software Data Protection
• Self-timed Write Cycle (5 ms Typical)
• High-reliability
– Endurance: One Million Write Cycles
– Data Retention: 100 Years
• AuTOmotive Grade Devices Available
• 8-lead PDIP, 8-lead JEDEC SOIC and 14-lead TSSOP Packages

Part Name(s) : Q67100-H3509 Q67100-H3510 Q67100-H3511 Q67100-H3514 Q67100-H3515 Q67100-H3516 Q67100-H3519 Q67100-H3520 Q67100-H3521 Q67100-H3522 Q67100-H3523 Q67100-H3524 SLA24C08-D-3/P SLA24C08-D/P SLA24C08-S-3/P SLA24C08-S/P SLA24C16-D-3/P SLA24C16-D/P SLA24C16-S-3/P SLA24C16-S/P SLE24C08-D/P SLE24C08-S/P SLE24C16-D/P SLE24C16-S/P SLX24C08/16/P Infineon
Infineon Technologies
Description : 8/16 Kbit (1024/2048 8 bit) SERIAL CMOS-EEPROM WITH I2C Synchronous 2-Wire BUS and Page Protection Mode? View

Features
• Data EEPROM internally organized as 1024/2048 bytes and 64/128 pages × 16 bytes
• Page protection mode, flexible page-by-page hardware write protection
    – Additional protection EEPROM of 64/128 bits, 1 bit per data page
    – Protection setting for each data page by writing its protection bit
    – Protection management WITHout switching WP pin
• Low power CMOS
• VCC = 2.7 TO 5.5 V operation
• Two wire SERIAL interface BUS, I2C-BUS compatible
• Filtered inputs for noise suppression WITH Schmitt trigger
• Clock frequency up TO 400 kHz
• High programming flexibility
    – Internal programming VOLTAGE
    – Self timed programming cycle including erase
    – Byte-write and page-write programming, between 1 and 16 bytes
    – Typical programming time 5 ms for up TO 16 bytes
• High reliability
    – Endurance 106 cycles1)
    – Data retention 40 years1)
    – ESD protection 4000 V on all pins
• 8 pin DIP/DSO packages
• Available for EXTENDED temperature ranges
    – Industrial: − 40 °C TO + 85 °C
    – AuTOmotive: − 40°C TO + 125 °C

Part Name(s) : SLA24C08-D-3/P SLA24C08-D/P SLA24C08-S-3/P SLA24C08-S/P SLA24C16-D-3/P SLA24C16-D/P SLA24C16-S-3/P SLA24C16-S/P SLE24C08-D/P SLE24C08-S/P SLE24C16-D/P SLE24C16-S/P SLX24C08/16/P Q67100-H3524 Q67100-H3521 Q67100-H3523 Q67100-H3520 Q67100-H3522 Q67100-H3519 Q67100-H3516 Q67100-H3511 Q67100-H3510 Q67100-H3515 Q67100-H3514 Q67100-H3509 Siemens
Siemens AG
Description : 8/16 Kbit (1024/2048 8 bit) SERIAL CMOS-EEPROM WITH I2C Synchronous 2-Wire BUS and Page Protection Mode? View

Features
• Data EEPROM internally organized as 1024/2048 bytes and 64/128 pages × 16 bytes
• Page protection mode, flexible page-by-page hardware write protection
    – Additional protection EEPROM of 64/128 bits, 1 bit per data page
    – Protection setting for each data page by writing its protection bit
    – Protection management WITHout switching WP pin
• Low power CMOS
• VCC = 2.7 TO 5.5 V operation
• Two wire SERIAL interface BUS, I2C-BUS compatible
• Filtered inputs for noise suppression WITH Schmitt trigger
• Clock frequency up TO 400 kHz
• High programming flexibility
    – Internal programming VOLTAGE
    – Self timed programming cycle including erase
    – Byte-write and page-write programming, between 1 and 16 bytes
    – Typical programming time 5 ms for up TO 16 bytes
• High reliability
    – Endurance 106 cycles1)
    – Data retention 40 years1)
    – ESD protection 4000 V on all pins
• 8 pin DIP/DSO packages
• Available for EXTENDED temperature ranges
    – Industrial: − 40 °C TO + 85 °C
    – AuTOmotive: − 40°C TO + 125 °C

Part Name(s) : AT24C01A-W2.7-11 AT24C02-W1.8-11 AT24C02N AT24C02U3-10UU-1 AT24C02Y1-10YU-1 AT24C04-W2.7-11 AT24C08A-W2.7-11 AT24C08AY5-10YU-1.8 AT24C16A-10PI-1.8 AT24C16A-10PI-2.7 AT24C16A-10TI-1.8 AT24C16A-10TI-2.7 AT24C16A-W2.7-11 AT24C16AN-10SI-1.8 AT24C16AN-10SI-2.7 AT24C16AY5-10YU-1.8 AT24CXX Atmel
Atmel Corporation
Description : Two-wire SERIAL EEPROM 1K (128 x 8) 2K (256 x 8) 4K (512 x 8) 8K (1024 x 8) 16K (2048 x 8) View

Description
The AT24C01A/02/04/08A/16A provides 1024/2048/4096/8192/16384 bits of SERIAL electrically erasable and programmable read-only memory (EEPROM) organized as 128/256/512/1024/2048 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-VOLTAGE operation are essential. 
The AT24C01A/02/04/08A/16A is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead MAP, 5-lead SOT23 (AT24C01A/AT24C02/AT24C04), 8-lead TSSOP, and 8-ball dBGA2 packages and is accessed via a Two-wire SERIAL inter face. In addition, the entire family is available in 2.7V (2.7V TO 5.5V) and 1.8V (1.8V TO 5.5V) versions.

Features
• Low-VOLTAGE and Standard-VOLTAGE Operation
– 2.7 (VCC= 2.7V TO 5.5V)
– 1.8 (VCC= 1.8V TO 5.5V)
• Internally Organized 128 x 8 (1K), 256 x 8 (2K), 512 x 8 (4K), 1024 x 8 (8K) or 2048 x 8 (16K)
• Two-wire SERIAL Interface
• Schmitt Trigger, Filtered Inputs for Noise Suppression
• Bidirectional Data Transfer ProTOcol
• 100 kHz (1.8V) and 400 kHz (2.7V, 5V) Compatibility
• Write Protect Pin for Hardware Data Protection
• 8-byte Page (1K, 2K), 16-byte Page (4K, 8K, 16K) Write Modes
• Partial Page Writes Allowed
• Self-timed Write Cycle (5 ms max)
• High-reliability
– Endurance: 1 Million Write Cycles
– Data Retention: 100 Years
• AuTOmotive Grade and Lead-free/Halogen-free Devices Available
• 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead MAP, 5-lead SOT23, 8-lead TSSOP and 8-ball dBGA2 Packages
• Die Sales: Wafer Form, Waffle Pack and Bumped Wafers

 

Part Name(s) : SLA24C164-D SLA24C164-D-3 SLA24C164-S SLA24C164-S-3 SLE24C164-D SLE24C164-S SLX24C164 Q67100-H3506 Q67100-H3501 Q67100-H3505 Q67100-H3500 Q67100-H3232 Q67100-H3233 Siemens
Siemens AG
Description : 8/16 Kbit 1024/2048 x 8 bit SERIAL CMOS EEPROMs/ I2C Synchronous 2-Wire BUS View

Description
The SLx 24C164 device is a SERIAL electrically erasable and programmable read only memory (EEPROM), organized as 2048 × 8 bit. The data memory is divided inTO 128 pages. The 16 bytes of a page can be programmed simultaneously.
   
Features
• Data EEPROM internally organized as
    2048 bytes and 128 pages × 16 bytes
• Low power CMOS
• VCC = 2.7 TO 5.5 V operation
• Two wire SERIAL interface BUS, I2C-BUS
    compatible
• Three chip select pins TO address 8 devices
• Filtered inputs for noise suppression WITH
    Schmitt trigger
• Clock frequency up TO 400 kHz
• High programming flexibility
    – Internal programming VOLTAGE
    – Self timed programming cycle including erase
    – Byte-write and page-write programming, between
        1 and 16 bytes
    – Typical programming time 5 ms for up TO 16 bytes
• High reliability
    – Endurance 106 cycles1)
    – Data retention 40 years1)
    – ESD protection 4000 V on all pins
• 8 pin DIP/DSO packages
• Available for EXTENDED temperature ranges
    – Industrial: − 40 °C TO + 85 °C
    – AuTOmotive: − 40 °C TO + 125 °C
   

1

2345678910 Next

All Rights Reserved © datasheetbank.com 2014 - 2020 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]