datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

P/N + Description + Content Search

Search Word's :
Part Name(s) : 74AC16374 74AC16374TTR
ST-Microelectronics
STMicroelectronics
Description : 16-BIT D-TYPE FLIP-FLOP WITH 3-STATE OUTPUTS (NON INVERTED)

DESCRIPTION
The 74AC16374 is an advanced high-speed CMOS 16-BIT D-TYPE FLIP-FLOP (3-STATE) fabricated WITH sub-micron silicon gate and double-layer metal wiring C2MOS tecnology.
This 16 bit D-TYPE FLIP-FLOP is controlled by two clock inputs (CK) and two output enable inputs (OE). The device can be used as two 8-bit FLIP-FLOPs or one 16-BIT FLIP-FLOP.
On the positive transition of the clock, the Q OUTPUTS will be set to the logic state that were setup at the D inputs.
While the (OE) input is low, the OUTPUTS will be in a normal logic state (high or low logic level); while OE is high, the OUTPUTS will be in a high impedance state.
The output control does not affect the internal operation of FLIP-FLOPs; that is, the old data can be retained or the new data can be entered even while the OUTPUTS are off.
All inputs and OUTPUTS are equipped WITH protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage.

■ HIGH SPEED:
   fMAX = 120MHz (TYP.) at VCC = 5V
■ LOW POWER DISSIPATION:
   ICC = 8µA(MAX.) at TA=25°C
■ HIGH NOISE IMMUNITY:
   VNIH = VNIL = 28 % VCC (MIN.)
■ 50Ω TRASMISSION LINE DRIVING CAPABILITY
■ SYMMETRICAL OUTPUT IMPEDANCE:
   |IOH| = IOL = 24mA (MIN)
■ OPERATING VOLTAGE RANGE:
   VCC (OPR) = 2V to 6V
■ IMPROVED LATCH-UP IMMUNITY

ST-Microelectronics
STMicroelectronics
Description : 16-BIT D-TYPE FLIP-FLOP WITH 3-STATE OUTPUTS (NON INVERTED)

DESCRIPTION
The 74ACT16374 is an advanced high-speed CMOS 16-BIT D-TYPE FLIP-FLOP (3-STATE) fabricated WITH sub-micron silicon gate and double-layer metal wiring C2MOS tecnology.
This 16 bit D-TYPE FLIP-FLOP is controlled by two clock inputs (CK) and two output enable inputs (OE). The device can be used as two 8-bit FLIP-FLOPs or one 16-BIT FLIP-FLOP.
On the positive transition of the clock, the Q OUTPUTS will be set to the logic state that were setup at the D inputs.
While the (OE) input is low, the OUTPUTS will be in a normal logic state (high or low logic level); while OE is high, the OUTPUTS will be in a high impedance state.
The output control does not affect the internal operation of FLIP-FLOPs; that is, the old data can be retained or the new data can be entered even while the OUTPUTS are off.
All inputs and OUTPUTS are equipped WITH protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage.

■ HIGH SPEED:
   fMAX = 120MHz (TYP.) at VCC = 5V
■ LOW POWER DISSIPATION:
   ICC = 8µA(MAX.) at TA=25°C
■ COMPATIBLE WITH TTL OUTPUTS
   VIH = 2V (MIN.), VIL = 0.8V (MAX.)
■ 50Ω TRANSMISSION LINE DRIVING CAPABILITY
■ SYMMETRICAL OUTPUT IMPEDANCE:
   |IOH| = IOL = 24mA (MIN)
■ OPERATING VOLTAGE RANGE:
   VCC (OPR) = 4.5V to 5.5V
■ IMPROVED LATCH-UP IMMUNITY

Part Name(s) : DM74LS534 DM74LS534N
Fairchild
Fairchild Semiconductor
Description : Octal D-TYPE FLIP-FLOP WITH 3-STATE OUTPUTS

General Description
The DM74LS534 is a high speed, low power octal D-TYPE FLIP-FLOP featuring separate D-TYPE inputs for each FLIP-FLOP and 3-STATE OUTPUTS for bus oriented applications. A buffered Clock (CP) and Output Enable (OE) is common to all FLIP-FLOPs. The DM74LS534 is the same as the DM74LS374 except that the OUTPUTS are INVERTED.

 

Description : Octal D-TYPE FLIP-FLOP WITH 3-STATE OUTPUTS

Octal D-TYPE FLIP-FLOP WITH 3-STATE OUTPUTS

The MC74AC534/74ACT534 is a high-speed, low-power octal D-TYPE FLIP-FLOP featuring separate D-TYPE inputs for each FLIP-FLOP and 3-STATE OUTPUTS for bus oriented applications. A buffered Clock (CP) and Output Enable (OE) are common to all flip flops. The ′AC/ACT534 is the same as the ′AC/ACT374 except that the OUTPUTS are INVERTED.

• Edge-Triggered D-TYPE Inputs
• Buffered Positive Edge-Triggered Clock
3-STATE OUTPUTS for Bus Oriented Applications

Description : Octal D-TYPE FLIP-FLOP WITH 3-STATE OUTPUTS

Octal D-TYPE FLIP-FLOP WITH 3-STATE OUTPUTS

The MC74AC374/74ACT374 is a high-speed, low-power octal D-TYPE FLIP-FLOP featuring separate D-TYPE inputs for each FLIP-FLOP and 3-STATE OUTPUTS for bus oriented applications. A buffered Clock (CP) and Output Enable (OE) are common to all FLIP-FLOPs.

• Buffered Positive Edge-Triggered Clock
3-STATE OUTPUTS for Bus-Oriented Applications
OUTPUTS Source/Sink 24 mA
• See MC74AC273 for Reset Version
• See MC74AC377 for Clock Enable Version
• See MC74AC373 for Transparent Latch Version
• See MC74AC574 for Broadside Pinout Version
• See MC74AC564 for Broadside Pinout Version WITH INVERTED OUTPUTS
• ′ACT374 Has TTL Compatible Inputs

Motorola
Motorola => Freescale
Description : OCTAL D-TYPE FLIP-FLOP WITH 3-STATE OUTPUTS

The MC54/74F534 is a high-speed, low-power octal D-TYPE FLIP-FLOP featuring separate D-TYPE inputs for each FLIP-FLOP and 3-STATE OUTPUTS for bus oriented applications. A buffered Clock (CP) and Output Enable (OE) are common to all FLIP-FLOPs. The F534 is the same as the F374 except that the OUTPUTS are INVERTED.

• Edge-Triggered D-TYPE Inputs
• Buffered Positive Edge-Triggered Clock
3-STATE OUTPUTS for Bus Oriented Applications

Description : Octal D-TYPE FLIP-FLOP WITH 3-STATE OUTPUTS

General Description
The ACT534 is a high-speed, low-power octal D-TYPE flip flop featuring separate D-TYPE inputs for each FLIP-FLOP and 3-STATE OUTPUTS for bus-oriented applications. A buffered Clock (CP) and Output Enable (OE) are common to all flip flops. The ACT534 is the same as the ACT374 except that the OUTPUTS are INVERTED.

Features
■ ICC and IOZ reduced by 50%
■ Edge-triggered D-TYPE inputs
■ Buffered positive edge-triggered clock
3-STATE OUTPUTS for bus-oriented applications
OUTPUTS source/sink 24 mA
■ ACT534 has TTL-compatible inputs
INVERTED output version of ACT374

Description : Octal D-TYPE FLIP-FLOP WITH 3-STATE OUTPUTS

Octal D-TYPE FLIP-FLOP WITH 3-STATE OUTPUTS

The MC74AC374/74ACT374 is a high-speed, low-power octal D-TYPE FLIP-FLOP featuring separate D-TYPE inputs for each FLIP-FLOP and 3-STATE OUTPUTS for bus oriented applications. A buffered Clock (CP) and Output Enable (OE) are common to all FLIP-FLOPs.

• Buffered Positive Edge-Triggered Clock
3-STATE OUTPUTS for Bus-Oriented Applications
OUTPUTS Source/Sink 24 mA
• See MC74AC273 for Reset Version
• See MC74AC377 for Clock Enable Version
• See MC74AC373 for Transparent Latch Version
• See MC74AC574 for Broadside Pinout Version
• See MC74AC564 for Broadside Pinout Version WITH INVERTED OUTPUTS
• ′ACT374 Has TTL Compatible Inputs

Fairchild
Fairchild Semiconductor
Description : Octal D-TYPE FLIP-FLOP WITH 3-STATE OUTPUTS

General Description
The 74F534 is a high speed, low-power octal D-TYPE FLIP-FLOP featuring separate D-TYPE inputs for each FLIP-FLOP and 3-STATE OUTPUTS for bus-oriented applications. A buffered Clock (CP) and Output Enable (OE) are common to all FLIP-FLOPs. The 74F534 is the same as the 74F374 except that the OUTPUTS are INVERTED.

Features
■ Edge-triggered D-TYPE inputs
■ Buffered positive edge-triggered clock
3-STATE OUTPUTS for bus-oriented applications

Description : 3.3V 16-BIT edge-triggered D-TYPE FLIP-FLOP (3-STATE)

DESCRIPTION
The 74LVT16374A is a high-performance BiCMOS product designed for VCC operation at 3.3V. This device is a 16-BIT edge-triggered D-TYPE FLIP-FLOP featuring NON-inverting 3-STATE OUTPUTS. The device can be used as two 8-bit FLIP-FLOPs or one 16-BIT FLIP-FLOP. On the positive transition of the clock (CP), the Q OUTPUTS of the FLIP-FLOP take on the logic levels set up at the D inputs.

FEATURES
16-BIT edge-triggered FLIP-FLOP
3-STATE buffers
• Output capability: +64mA/-32mA
• TTL input and output switching levels
• Input and output interface capability to systems at 5V supply
• Bus-hold data inputs eliminate the need for external pull-up resistors to hold unused inputs
• Live insertion/extraction permitted
• Power-up reset
• Power-up 3-STATE
• No bus current loading when output is tied to 5V bus
• Latch-up protection exceeds 500mA per JEDEC Std 17
• ESD protection exceeds 2000V per MIL STD 883 Method 3015 and 200V per Machine Model

12345678910 Next

All Rights Reserved© datasheetbank.com  [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]